Accepted Manuscript Bioelectrochemical reduction of volatile fatty acids in anaerobic digestion effluent for the production of biofuels Sanath Kondaveeti, Booki Min PII:
S0043-1354(15)30223-2
DOI:
10.1016/j.watres.2015.09.011
Reference:
WR 11519
To appear in:
Water Research
Received Date: 8 June 2015 Revised Date:
30 August 2015
Accepted Date: 5 September 2015
Please cite this article as: Kondaveeti, S., Min, B., Bioelectrochemical reduction of volatile fatty acids in anaerobic digestion effluent for the production of biofuels, Water Research (2015), doi: 10.1016/ j.watres.2015.09.011. This is a PDF file of an unedited manuscript that has been accepted for publication. As a service to our customers we are providing this early version of the manuscript. The manuscript will undergo copyediting, typesetting, and review of the resulting proof before it is published in its final form. Please note that during the production process errors may be discovered which could affect the content, and all legal disclaimers that apply to the journal pertain.
ACCEPTED MANUSCRIPT
Bioelectrochemical reduction of volatile fatty acids in anaerobic
2
digestion effluent for the production of biofuels
3
Sanath Kondaveeti and Booki Min*
RI PT
1
4
Department of Environmental Science and Engineering, Kyung Hee University,
6
1 Seocheon-dong, Yongin-si, Gyeonggi-do 446-701, Republic of Korea
M AN U
SC
5
7
8
TE D
9
10
12
13
14
15
16
17
∗
AC C
EP
11
Corresponding author; Tel.: +8231-201-2463 (office); E-mail address:
[email protected] (Booki Min)
ACCEPTED MANUSCRIPT
Abstract
2
This study proves for the first time the feasibility of biofuel production from anaerobic digestion
3
effluent via bioelectrochemical cell operation at various applied cell voltages (1.0, 1.5 and 2.0 V).
4
An increase in cell voltage from 1 to 2 V resulted in more reduction current generation (-0.48 to -
5
0.78 mA) at a lowered cathode potential (-0.45 to -0.84 mV vs Ag/AgCl). Various alcohols were
6
produced depending on applied cell voltages, and the main products were butanol, ethanol, and
7
propanol. Hydrogen and methane production were also observed in the headspace of the cell. A
8
large amount of lactic acid was unexpectedly formed at all conditions, which might be the
9
primary cause of the limited biofuel production. The addition of neutral red (NR) to the system
10
could increase the cathodic reduction current, and thus more biofuels were produced with an
11
enhanced alcohol formation compared to without a mediator.
M AN U
SC
RI PT
1
TE D
12
Keywords: Bioelectrochemical cell operation, Biofuel, Biocathode, Mediators, Anaerobic
14
digestion effluent
16
17
18
AC C
15
EP
13
19
20
2
ACCEPTED MANUSCRIPT
1 1. Introduction
The substantial decrease in fossil fuels has resulted in the search for alternative and low-
3
cost methods of energy production (Kakarla and Min 2014). In this respect, bioelectrochemcial
4
systems (BESs) have gained immense attention for generating electricity and biofuels with the
5
simultaneous treatment of organic waste and wastewater(Kondaveeti et al. 2014). The
6
potentiality of BES application for biofuel production has been evaluated for hydrogen,
7
methane(Cheng et al. 2009, Logan et al. 2008), and other value-added products (Rabaey and
8
Rozendal 2010)using a bioelectrocatalyzed cathode electrode. In the process of biofuel
9
generation using BES, an external power supply serves as the energy source that drives the
10
microbial electrochemical reduction of proton ions, carbon dioxide (CO2), and volatile fatty acids
11
(Sharma et al. 2013). However, biofuel production in BESs is still in the beginning stages, and
12
requires improvement in several areas to make it commercially available (Srikanth et al. 2014).
TE D
M AN U
SC
RI PT
2
In general, biofuels production from organic sources are limited to complex substrates
14
such as lignocelluloses and wheat straw hydrolysate, which are further reduced to simple
15
substrates (Acetic and butyric acid) (Srikanth et al. 2014). In this aspect, anaerobic digestion
16
(AD) effluent with volatile fatty acids such as acetic and butyric acid can serve as organic
17
compounds for biofuel production (Spirito et al. 2014).In typical wastewater treatment plants
18
(WWTP), the effluent from AD are subjected to activated sludge systems or recycled for further
19
treatment processes (Appels et al. 2008).These biofuel generations from AD effluent can be
20
enhanced using exocellular mediators to modify energy metabolism. Mediator compounds cycle
21
between oxidized and reduced states and play a vital role in bacterial metabolism by creating an
22
additional electron flow and thereby enhancing biofuel production. Mediators such as neutral red
23
(NR), methyl viologen (MV), methylene blue (MB), and anthraquinone disulfonate (AQDS) are
AC C
EP
13
3
ACCEPTED MANUSCRIPT
used in ABE (Acetone-Butanol-Ethanol) fermentation systems and in BES to shift fermentative
2
metabolism to biofuel (bioalcohol and biogas) synthesis and to limit organic acid synthesis
3
(Steinbusch et al. 2009, Yarlagadda et al. 2012). Although the exact mechanism of how
4
mediators regulate fermentative pathways is not fully understood, the supplementation of
5
mediators is an attractive method for enhancing the electron flow from organic acids to biofuels.
RI PT
1
The primary objective of the present study is to evaluate the feasibility of using anaerobic
7
digestion effluent to generate biofuels (bioalcohol and biogas) in bioelectochemical systems
8
(BES) with the help of an external power supply. A bioelectrochemical cell (BES) operation was
9
performed using an abiotic anode electrode and biocatalyzed cathode electrode for the formation
10
of biofuel in a cathode chamber. The production of biofuel from anaerobic digestion effluent was
11
tested at various external power inputs (1.0, 1.5 and 2 V), and the effect of mediators (Neutral
12
red; NR) was also evaluated. The presence of NR has been known to influence the bacterial
13
exocellular electron transfer metabolism with elevated current generations. Electrochemical
14
techniques such as cyclic voltammetry (CV) were pursued for a better understanding of BES
15
operation with AD effluent and in the presence of mediators.
M AN U
TE D
EP
17
2. Materials and Methods
AC C
16
SC
6
18
2.1Microbial inoculum and electrolyte
19
Inoculum for the microbial consortium and anaerobic digestion (AD) effluent for the cathode
20
compartment were obtained from Yongin Respia Wastewater Treatment Plant (Yongin-si,
21
Korea). The initial concentrations of VFAs in AD effluent were 0.5±0.04 (Acetic acid) and
22
1.84±0.19 g/l(Butyric acid), respectively. The electrolyte for BES operation in the absence of 4
ACCEPTED MANUSCRIPT
planktonic cells (suspended culture) was pursued using growth media (GM). The GM consisted
2
of a vitamin and mineral solution and was prepared as described in previous studies (Kakarla and
3
Min 2014).
4
5
2.2 Mediator for microbial redox reactions
RI PT
1
The external supplementation of mediators can provide an alternative electron flow by
7
enhancing the production of biofuel, and also can accelerate power generations due to variations
8
in the physiology of bacteria.NR was selected based on certain characteristics such as high
9
solubility, complete reversibility, stability and lack of combination with other molecules(Fultz
10
and Durst 1982). Moreover, one of the primary biocomponents involved in microbial redox
11
reactions is NADH, with a redox potential of -320 mV, as similar to NR (-325 mV). NR was
12
demonstrated to be biologically active in anaerobic conditions; mediator was used in
13
concentrations (1 mM) similar to those used in other research studies (Steinbusch et al. 2009).
16
M AN U
TE D
EP
15
2.3 Bioelectrochemical system set-up and operation A double chamber “H” type BES cell with two compartments was chosen and operated in
AC C
14
SC
6
17
fed-batch mode by varying the external cell voltages. Each compartment cell consisted of 200 ml
18
as a working volume with a total volume of 250 ml. Platinum-coated carbon paper (0.5 mg/cm2)
19
with a surface area of 40 cm2 was used as an anode, and a carbon brush (3 × 2.5 cm) was used as
20
cathode. The carbon brush cathode was prepared by twisting the carbon fibers with stainless steel
21
wire. The electrical connections on the electrode were established using copper wire and by
5
ACCEPTED MANUSCRIPT
sealing the contact area with non-conductive epoxy resin. The anode and cathode compartments
2
were separated using pretreated Nafion-117 (PEM; Dupont Co., USA). The membrane and
3
cathode electrode (carbon brush) pretreatment were pursued as described in previous literatures
4
(Feng et al. 2010, Moon et al. 2014). To avoid membrane swelling when placed in BES,
5
pretreated membranes were stored in deionized water and taken out prior to being used. Ag/AgCl
6
(sat’d NaCl) from bio analytical instruments (USA) was used as a reference electrode in the
7
cathode chamber during the electrochemical analysis and for noting cathode potentials. The
8
anode and cathode electrodes were connected to a DC power supply and various external energy
9
inputs (1.0, 1.5 and 2 V) were supplemented(Huang et al. 2013).
M AN U
SC
RI PT
1
Catholyte consists of either AD effluent or GM, as per requirements. Prior to
11
supplementation, the cathode influent pH was adjusted to 6 using either 1 M HCl or NaOH. In
12
both cases, the anode chamber of the reactor consisted of GM (pH 6). The cathode and anode
13
solutions were continuously stirred for effective mixing and operated in a temperature-controlled
14
incubator at 30±2oC.BES reactors were sealed using silicone gel to ensure strict anaerobic
15
conditions. Prior to sealing of the BES reactors, headspace and solutions were purged with
16
nitrogen gas for 15 to 20 min, minimizing the effect of dissolved oxygen. The anolyte and
17
catholyte were replaced when a decrease in cell voltage was noticed. After 94 days of operation
18
with AD effluent, the electrically-active biocathode electrode was transferred to fresh growth
19
medium and operated at 1.5 V with similar concentrations of acetic and butyric acid.
EP
AC C
20
TE D
10
Along with BES, three additional sets of reactors were operated as a control. The first
21
control reactor was operated similar to the BES with the exception of sterilization (autoclaving)
22
of the cathode solutions (Anaerobic digestion effluent). The second control reactor was operated
23
by maintaining abiotic cathode (no inoculums) conditions with an external supplement of acetic 6
ACCEPTED MANUSCRIPT
and butyric acids. The third control reactor was operated without supplementation of external
2
energy (open circuit conditions).These control experiments were pursued to illustrate the
3
importance of biological catalyst (biofilm), as well as the influence of external cell voltage to
4
crossover thermodynamic barriers for product formation. All experiments and analysis were
5
pursued in replicated (duplicate or triplicate) cycles to maintain consistency.
RI PT
1
7
SC
6
2.4 Analytical Methods
For liquid analysis, 10 ml of samples were collected at the end of operation (4 to 6 days)
9
using a sterile and nitrogen-purged syringe. The collected samples were filtered using an
10
acrodisc (0.2 µm) syringe filter.VFA concentrations in the liquid phase were measured using an
11
ion chromatogram (IC-861, Metrohm, USA) equipped with an organic acid column (model:
12
Metrosep 250/7.8, Metrohm, USA). Head-space biogas analyses were pursued using a gas
13
chromatograph (Younglin Instruments, Korea) equipped with a thermal conductivity detector
14
(TCD) and carboxen column (Supelco, USA). The oven temperature was maintained at 150oC,
15
whereas the injector and detector temperatures were 100 and 200 oC, respectively. Nitrogen gas
16
was used as a carrier at a flow rate of 6 ml/min. Sampling was performed with a sterile gas-tight
17
syringe (Hamilton, USA) and analyzed immediately. Bioalcohols such as ethanol, methanol,
18
proponol, acetone, glycerol, butanol etc. were analyzed using gas chromatography (GC; Agilent,
19
USA) equipped with a flame ionization detector (FID) and fitted with an HP innowax column
20
(Agilent, USA). The injector, oven, and detector temperatures were 150, 220, and 230oC,
21
respectively. Helium was used as a carrier gas with a flow rate of 5ml/min. All analytical
22
systems (GC and IC) were calibrated with standard chemicals in a range of sample
AC C
EP
TE D
M AN U
8
7
ACCEPTED MANUSCRIPT
1
concentrations. The GC and IC sample preparations were pursued as described in previous
2
studies (Merzougui et al. 2011).
RI PT
3
2.5 Electrochemical measurements and calculations
5
External energy inputs of 1.0, 1.5, and 2.0 volts were applied to test the effect of voltage on
6
product formation. The desired external voltage was applied to the circuit using a DC power
7
supply. The negative lead of the power source was connected to the cathode with an external
8
resistance of 15 Ω and the positive lead of the circuit was connected directly to the anode. The
9
voltage was measured across an external resistor with a 5 min time interval using a data
10
acquisition system in a personal computer. Cyclic voltammetry (CV) analyses were pursued to
11
analyze the effect of mediators in BES using a potentiostat(Versa Stat 3, Princeton Applied
12
Research, USA).CV measurements were evaluated within a range of -0.9 to 0.9 V (vs. Ag/AgCl)
13
at a scan rate of 5 mV/s.
TE D
M AN U
SC
4
The Coulombic efficiency (CE) of BES, using a bioelectrocatalyzed cathode for the
15
reduction of VFAs (Acetic and Butyric acid), was calculated by dividing the Coulombs of the
16
product (Ca) by the total coulombs (CI). Total Coulombs were obtained by integrating the area
17
under the current vs. time (I-t curve). The amount of Coulombs (Ca) distributed in the moles of
18
individual products (ni) by BES in the process of the bioelectrocatalyzed reduction of VFAs was
19
calculated by following Equations included in the body of the text should be punctuated
20
accordingly. (Marshall et al. 2012):
21
AC C
EP
14
Ca= Fbini,Eq. (1)
8
ACCEPTED MANUSCRIPT
1
where bi is the number of electrons in the product; F is Faraday constant (96,485 C/mol); and n is the number of moles of product.
3
Capacitance and energy calculations were performed by analyzing the CV data (Raghavulu et al.
4
2012) using the following equation:
=
, Eq. (2)
SC
5
RI PT
2
where C is the capacitance (F), Q0 is the charge obtained (C), and V0 is the maximum applied
7
voltage (V).
M AN U
6
8
9
3. Results and discussion
3.1 Current generation in the bioelectrochemical reduction process
11
Reductive biocatalytic current generations were observed in BES at various applied voltages
12
(1.0, 1.5 and 2.0 V) by measuring the cell voltage across the external resistor (Fig.1, Table 2).
13
Based on other studies (Sharma et al. 2013, Srikanth et al. 2014), it is presumed that the applied
14
voltages used in this study were sufficient to reach activation energy. Initial current generations
15
without mediator were observed after 18 days of operation with an applied voltage of 1 V, and
16
the applied voltage was further increased to 1.5 and 2V. At 1 V, the current generation and
17
cathode potentials (vs Ag/AgCl) were -0.48±0.03 mA and -0.45±0.02 V, respectively. The
18
current generations and cathode potentials were further enhanced to -0.64±0.02 mA and -
19
0.68±0.018 V, with operation at 1.5 V. Reductive current appeared to increase with increases in
20
applied voltages; at 2 V the BES current generation and cathode potentials were-0.78 ± 0.01 mA
21
and -0.84 ± 0.032V, respectively.
AC C
EP
TE D
10
9
ACCEPTED MANUSCRIPT
After 63 days of operation, 1mM of neutral red was added to the cathode chamber as a
2
mediator for the bioelectochemical reduction. Increased current generation and cathode
3
potentials were noticed in the presence of the mediator. The variation of external cell voltage (1,
4
1.5, and 2 V) with neutral red mediator resulted in enhanced cell voltages of -0.52±0.016,-
5
0.7±0.021, -1.1±0.018 mA and cathode potentials of -0.51±0.014, -0.69±0.016, and -0.89 ±0.018
6
V, respectively. Elevated current generations were observed in the presence of mediator due to
7
the enhanced extra cellular electron transfer metabolism of biocatalytic activity. Steinbush et al.,
8
demonstrated similar results for increased current generation in the presence of mediators
9
(Steinbusch et al. 2009). In their study, initial current generation of 7.8 mA was amplified to18.5
SC
M AN U
10
RI PT
1
mA using methyl viologen (MV) as a mediator.
The bioelectochemical cell operation at 1.5 V with synthetic growth media and
12
externally-supplemented acetic and butyric acid and in the absence of planktonic cells exhibited
13
an immediate (0.8 d) reduction in current of -0.78 ± 0.032 mA (Fig S1). This result suggests that
14
the bioelectrochemical reduction was obtained via the biocatalytic activity of microorganisms
15
attached to the cathode electrode. No current generation and biofuels formation were observed in
16
the BES control reactors (Fig. S2).
EP
TE D
11
AC C
17
18
3.2Bioalcohol and biogas production from the bioelectrochemcial reduction of anaerobic
19
digestion effluent
20
The product profiles represented here were drawn after examination in replicated cycles, and the
21
results obtained are within the border of experimental errors. The characteristics of AD effluent
22
used in the BES reactor were analyzed using standard methods (APHA 2005), as presented in 10
ACCEPTED MANUSCRIPT
Table 1. The initial concentrations of acetic and butyric acids in anaerobic digestion effluent
2
were 0.5±0.04 and 1.84±0.19 g/l, respectively (Fig. 2). Bioelectrochemical reduction at 1volt
3
revealed no bioalcohol generations (Fig. 2a), which might be due to a smaller cathodic potential
4
(-0.45 V) (Rabaey and Rozendal 2010). By increasing the applied voltages (1.5 and 2 V), the
5
bioelectrocatalyzed synthesis of bioalcohols was observed as represented in Fig 2a.At 1.5V, the
6
concentration of ethanol and butanol were 31 and 57 mg/l, respectively. The ethanol
7
concentration (31 mg/l) at 1.5V in this study was smaller than the value (50 mg/l) from the other
8
BES operation (Sharma et al., 2013). This difference in ethanol production may be due to
9
different initial concentration of acetic acid (100 mM vs 8.3 mM in this study) and butyric acid
10
(100 mM vs 20 mM in this study). By increasing the cell voltage to 2 V, amplifications in
11
product profiles were observed. Butanol (91 mg/l) and proponol (60 mg/l) were the main
12
products observed, and other alcohols were in range of 50 mg/l. Although ethanol production
13
was observed at 1.5 V, it was not observed at 2 V, possibly due to the further reduction of
14
ethanol to other products or the usage of ethanol as a bacterial substrate (Müller 2001, Sharma et
15
al. 2013). Several researchers reported that oxidation of ethanol in ABE fermentation favored the
16
synthesizing of butyrate and propionate (Agler et al. 2011). The product profiles observed in this
17
study at 2 V with a cathode potential of -840 mV (vs Ag/AgCl) were similar to other studies
18
operating with a working electrode (cathode) potential of -850mV (Sharma et al. 2013). In their
19
study, the concentrations of butanol and proponol were 100 and 87 mg/l, respectively.
SC
M AN U
TE D
EP
AC C
20
RI PT
1
BES operation at various external cell voltages of 1, 1.5, and 2 V resulted in hydrogen
21
(H2) and methane (CH4) as predominant headspace biogas products (Fig 2b). No methane
22
generation was noticed with applied voltages of 1 V and 1.5 V; whereas at 2 V, methane
23
generation was observed at 11±2.1%. An increase in hydrogen generation was noticed with 11
ACCEPTED MANUSCRIPT
increase in applied voltages. The percentages of hydrogen in the headspace at 1, 1.5, and 2 V
2
were 3.7±0.5, 7.2±0.8 and 25.4±1.3% respectively. No bioalcohol and current generation were
3
detected in the BES control reactor, suggesting that product formation was solely due to
4
bioelectrocatalytic activity on the cathode electrode. The hydrogen gas concentrations in the
5
control at various voltages (1, 1.5, and 2 V) were 1.6±0.4 2.0±0.1, and 5.9±1.1%, respectively.
RI PT
1
SC
6
3.3 Cyclic voltammogram of bioelectochemical reduction of anaerobic digestion effluent
8
both with and without mediator
9
Cyclic voltammetry (CV) techniques help to determine the ability of biocatalysts on an electrode
10
surface to drive reductive reactions. In the present study, CV was used to pinpoint the influence
11
of extra cellular mediators on the biocatalyst to show a charge transfer phenomenon. The CV
12
profiles indicated variations in electrochemical behavior in the presence of mediators (Fig. 3).
13
The catalytic currents were similar with variation in the supplementation of mediators; however
14
a significant variation in peak current was noticed with increases in mediator concentration (0 to
15
1 mM). This might be due to the unidirectional pass of electrons from electrode to NR and
16
NADH (Park and Zeikus 2000). The reductive peak potential with various concentrations (0, 0.5,
17
0.7 and 1 mM) of an exocellular mediator was noticed at around -410 to -450 mV (vs. Ag/ AgCl)
18
with variations in peak current. The bioelectrochemical reduction of fumarate to succinate in the
19
other study exhibited a redox potential of about -520 mV (vs. Ag/AgCl) in the presence of NR
20
mediator (Park and Zeikus 1999). BES operation without mediators and with various
21
concentrations of mediators (0.5, 0.75, and 1mM) resulted in peak currents of -0.11, -0.14, -0.19,
22
and -0.28 mA, respectively.
AC C
EP
TE D
M AN U
7
12
ACCEPTED MANUSCRIPT
This redox-coupled reaction of NR with NADH might increase the synthesis of ethanol
2
and butanol, which was also indicated by enhanced alcohol formation with mediator, as shown in
3
Fig.4. The charge and capacitance were calculated based on the voltammetric profiles. Charge is
4
an indicator of the number of electrons available at an instant during an electrochemical reaction
5
(Kondaveeti and Min 2013). The bioelectrochemical reduction processes both without and with
6
NR mediator (1 mM) exhibited 3.1× 10-3and 7 × 10-3 C, respectively. This result suggests that
7
the presence of mediator in BES for bioelectrochemical reduction processes can increase the
8
availability of electrons for favorable reductive reactions. Capacitance is a measurement for the
9
amount of electrical charge stored at a maximum applied potential. These charges stored in
10
capacitive electrodes are directly proportional to the migration of electrons towards the electrode.
11
Similar to charge, higher capacitance values were noticed in BES with the presence of mediator
12
(7.7 mF) in comparison to without mediator (3.5 mF). These values indicate that the enhanced
13
holding capacity of charge with mediator can increase biofuel synthesis as shown in previous
14
studies (Srikanth et al. 2014).
15
16
3.4
EP
TE D
M AN U
SC
RI PT
1
The effect of mediator on biofuel (bioalcohol and biogas) production
In the presence of mediator (NR), the formation of biofuel production was detected with the
18
consecutive initiation of electron utilization (Fig.4). Accordingly, it is assumed that product
19
synthesis was the consequence of electro-catalyzed biofilm reductive reactions. At 1 V (Cathode
20
potential: -0.51 V), ethanol, proponol, and butanol appear in concentrations of 19.8 mg/l, 30
21
mg/l, and 31 mg/l, respectively (Fig 4a). These concentrations were lower in comparison to
22
other studies (Steinbusch et al. 2009) carried out by Steinbusch et al., where acetic acid was
AC C
17
13
ACCEPTED MANUSCRIPT
used as an electron acceptor (Cathode potential: -0.55 V). In their study, ethanol concentrations
2
of 83 mg/l were noticed using upflow anaerobic sludge blanket (UASB) reactor inoculum; with
3
methyl viologen as an external cellular mediator. The lower concentration of ethanol generation
4
might be due to variations in reactor configuration (flat plate vs. double chamber), type of
5
mediator (methyl viologen vs. neutral red), concentration of substrate, and biological activity on
6
the cathode electrode. These concentrations of ethanol were higher with increases in applied cell
7
voltage. At 1.5 V; ethanol (50 mg/l) and butanol (70 mg/l) were noticed as predominant
8
bioalcohols, where as the propanol concentration was 40 mg/l.
M AN U
SC
RI PT
1
Bioelectrochemical cell operation at 2 V (cathode potential: -0.9 V) exhibited butanoland
10
ethanol formations in concentrations of 130 mg/l and 49.8 mg/l, respectively. The concentration
11
profile observed at 2 V (Cathode potential: -0.9 V) was higher in comparison to recent studies
12
pursued by Sharma et al., where mixed cultures of sulfate reducers were used as the predominant
13
bacteria on a working electrode (Cathode potential: -0.85 V). In their study, they produced up
14
to50 mg/l of ethanol and 100 mg/l of butanol as bioalcohols. The amplified production of butanol
15
in comparison to other studies might be due to the usage of redox mediators (Girbal et al. 1995,
16
Yarlagadda et al. 2012).Proponol (41 mg/l) and butanol (47 mg/l) were prevalent bioalcohols
17
recorded in BES by transferring the electrocatalyzed biofilm electrode into growth media with
18
similar concentrations of acetic and butyric acids as in anaerobic digestion effluent (Fig S1,
19
Table 2).
EP
AC C
20
TE D
9
The presence of neutral red (mediator) enhanced the generation of biogas (hydrogen and
21
methane)(Fig 2b). The hydrogen production of 15.1±1.7, 26.3±2.1, and 31.8±2.4 % was
22
observed at cell voltages of 1, 1.5, and 2V, respectively. The overall concentration of methane
23
was less than 9.4±1.6% in the headspace. The absence of bioalcohol formations and current 14
ACCEPTED MANUSCRIPT
generations was noticed in the BES control reactors. The hydrogen gas concentrations at external
2
supplemented voltages of 1, 1.5, and 2 V were 5.9±0.7, 8.7±1.4, and 10.9±1.4%, respectively.
3
During BES operation with AD effluent and in the presence of NR at various cell voltages; the
4
initial catholyte pH of 6.0 was decreased to 4.9 ± 0.2.The decrease in catholyte pH might be due
5
to an increased concentration of biofuels (Nevin et al. 2010, Rabaey and Rozendal 2010). No
6
variation in pH was observed in BES control reactors at various applied voltages.
SC
7
RI PT
1
3.5Coulombs distribution in synthesized products from anaerobic digestion effluent The Columbic efficiency (CE) is defined as the percentage of supplied electrons to final products
9
in a cathode. The CE was calculated at both operational conditions (the presence and absence of
10
mediator) with various applied voltages (1, 1.5 and 2 V) using anaerobic digestion effluent as
11
catholyte. The distributions of Coulomb into biofuels and end products were calculated and are
12
depicted in Fig. 5. BES operation at various cell voltages (1, 1.5 and 2 V) with anaerobic
13
digestive effluent (Fig. 5a) exhibited total Coulombs (supplemented electrons) of 77165, 277055,
14
175525 C and total CE of20, 4.9, and 9.8%, respectively. The total Coulombs from current
15
generation were higher in the BES operation with the supplementation of mediators, due to
16
variations in bacterial extra cellular activity. The presence of mediator (Fig. 5b) and operation
17
with various external cell voltages (1, 1.5 and 2 V) resulted in total coulombs (supplemented
18
electrons) of 80051, 177870, and 243493 C, and CE of 15, 8, and 7.8 % respectively. Total
19
Coulombs were distributed to diversified products of biofuels (bioalcohols and biogas) in both
20
operational conditions. The BES operation with anaerobic digestion effluent at various external
21
cell voltages (1, 1.5 and 2 V) for biofuel production resulted in Coulombs of 22.3, 4064, 7426 C,
22
and CE of0.029, 1.5, and 4.2%, respectively. With the supplementation of mediator, the
23
Coulombs of biofuels at voltages of 1, 1.5, and 2 V were increased to 2811, 5226, and 8279 C,
AC C
EP
TE D
M AN U
8
15
ACCEPTED MANUSCRIPT
respectively, and the CEs were 3.5, 2.9, and 3.5 %. BES operation at 1.5 V with GM containing
2
acetic and butyric acids exhibited a total Coulombs (current)of 89116, 4130, and a CE for
3
biofuels of4.6 %.The CE observed in this study were slightly smaller (11~24 %), in comparison
4
to other studies of BES operation for VFAs reduction at -0.85V (Sharma et al. 2013, Sharma et
5
al. 2014).The product recovery (conversion) percentage based on the Coulombs of VFAs
6
supplemented (45923 C) in the BES operation using AD effluent at various external cell voltages
7
(1, 1.5, and 2 V) are 28, 29, and 34 %, respectively. These values are amplified with the
8
supplementation of mediators, due to increased biofuel concentrations. During BES operation in
9
the presence of mediators, the recovery (conversion) percentages based on Coulombs of VFAs
10
supplemented (46698 C) at various external cell voltages (1, 1.5 and 2 V,) are 30, 31, and 40 %,
11
respectively. By changing the catholyte solution from AD effluent to GM media, the recovery
12
(conversion) percentage based on Coulombs VFAs supplemented (43688 C) was decreased to 13
13
%, due to decremented biofuels concentration. The recovery percentages noticed in this study
14
were similar in comparison to other BES (30 %)studies using CO2to generate value-added
15
products(Annie Modestra et al. 2015).
TE D
M AN U
SC
RI PT
1
Lactic and formic acids were observed as major byproducts of BES operation with
17
anaerobic digestion effluent and in the presence of mediator. The coulombic efficiency of lactic
18
acid as a byproduct at various cell voltages (1, 1.5, and 2 V) and with anaerobic digestion
19
effluent were 6.6, 2.9, and 4.6 %, respectively. In the presence of mediator, the coulombic
20
efficiencies of lactic acid were 8.2 (1 V), 4.1 (1.5 V), and 3.5 %( 2 V). The generation of lactic
21
acid in BES from reductive substrates such as acetic and butyric acids can be detrimental to
22
biofuels formation. Although the production of large amounts of lactic acid compared to the
23
other alcohols could not be clearly understood in this study, some operational conditions such as
AC C
EP
16
16
ACCEPTED MANUSCRIPT
pH, dissolved solid, and temperature may be used as the controlling factor to enhance biofuel
2
production by eliminating lactic acid–producing bacteria (Narendranath and Power 2005).
3
Alternatively, lactic acid can be used for the synthesis of bioplastics, and also used as acidulant,
4
favoring and preservative in food industry (Abdel-Rahman et al. 2013, Venkateswar Reddy et al.
5
2014). Recent studies carried out by Sharma et al., using VFAs (acetic and butyric acids) as
6
electron acceptor, also observed lactic acid (1.5 g/l) as a predominant byproduct(Sharma et al.
7
2013).The major interference noticed in the conversion of electrical energy into organic
8
chemicals using BES were selective transformations of product at consistent kinetic rates
9
inbiocathodes.BES operation was pursued with a simple combination of acetic and butyric acids
10
from anaerobic digestion effluent; however, the biofuels (bioalcohols and biogas) were
11
diversified. Moreover the presence of mediator did not alter the biofuel formation, but enhanced
12
the end product concentration. This was possibly due to the presence of various microorganisms
13
in the cathode biofilm, or to the various metabolic pathways of bacteria(Wu et al. 2012).
14
Therefore, further research in biocathodes using advanced cell configuration is needed to achieve
15
higher conversion rates and specificity of product formation at low cost. This is also essential in
16
the separating and recovery of fermentation products. Recently, Lu and his co-workers (Lu and
17
Li 2014)developed a gas-stripping process for the extraction of solvents from fermentation
18
processes. This is of special interest because products synthesized in the BES process can be
19
easily coupled to their system, with the simultaneous synthesis and recovery of products.
SC
M AN U
TE D
EP
AC C
20
RI PT
1
21
Conclusion
22
The bioelectrochemcial reduction of anaerobic digestion effluent at various applied cell voltages
23
was evaluated for biofuel production. Increases in current (-0.48 to -0.78 mA) generation and
17
ACCEPTED MANUSCRIPT
biofuels concentration were noticed with increased applied voltages (1, 1.5, and 2 V). Ethanol,
2
butanol, and proponol were determined to be predominant bioalcohols. Hydrogen and methane
3
were present in the headspace biogas. The concentrations of biofuels were amplified with the
4
supplementation of mediators due to increases in current generation and capacitance. Enhanced
5
biofuels and specificity in biofuels can be resolved in further optimized bioelectrochemcial
6
reduction processes.
RI PT
1
SC
7
Acknowledgments:
9
The authors would like to thank Professor Hong Liu for providing valuable comments on the
10
manuscript. This study was funded by a National Research Foundation of Korea Grant
11
(2012R1A1A2042031) and BK plus 21 (20140260).
M AN U
8
TE D
12
References
14
Abdel-Rahman, M.A., Tashiro, Y. and Sonomoto, K. (2013) Recent advances in lactic acid
15
production by microbial fermentation processes. Biotechnology Advances 31(6), 877-902.
16
Agler, M.T., Wrenn, B.A., Zinder, S.H. and Angenent, L.T. (2011) Waste to bioproduct
17
conversion with undefined mixed cultures: the carboxylate platform. Trends in Biotechnology
18
29(2), 70-78.
19
Annie Modestra, J., Navaneeth, B. and Venkata Mohan, S. (2015) Bio-electrocatalytic reduction
20
of CO2: Enrichment of homoacetogens and pH optimization towards enhancement of carboxylic
21
acids biosynthesis. Journal of CO2 Utilization 10(0), 78-87.
AC C
EP
13
18
ACCEPTED MANUSCRIPT
APHA (2005) Standard Methods for the Examinatinon of Water and Wastewater., American
2
Public Health Association, , Washing ton, DC.
3
Appels, L., Baeyens, J., Degrève, J. and Dewil, R. (2008) Principles and potential of the
4
anaerobic digestion of waste-activated sludge. Progress in Energy and Combustion Science
5
34(6), 755-781.
6
Cheng, S., Xing, D., Call, D.F. and Logan, B.E. (2009) Direct Biological Conversion of
7
Electrical Current into Methane by Electromethanogenesis. Environmental Science &
8
Technology 43(10), 3953-3958.
9
Feng, Y., Yang, Q., Wang, X. and Logan, B.E. (2010) Treatment of carbon fiber brush anodes
10
for improving power generation in air–cathode microbial fuel cells. Journal of Power Sources
11
195(7), 1841-1844.
12
Fultz, M.L. and Durst, R.A. (1982) Mediator compounds for the electrochemical study of
13
biological redox systems: a compilation. Analytica Chimica Acta 140(1), 1-18.
14
Girbal, L., Croux, C., Vasconcelos, I. and Soucaille, P. (1995) Regulation of metabolic shifts in
15
Clostridium acetobutylicum ATCC 824. FEMS Microbiology Reviews 17(3), 287-297.
16
Huang, L., Guo, R., Jiang, L., Quan, X., Sun, Y. and Chen, G. (2013) Cobalt leaching from
17
lithium cobalt oxide in microbial electrolysis cells. Chemical Engineering Journal 220(0), 72-80.
18
Kakarla, R. and Min, B. (2014) Photoautotrophic microalgae Scenedesmus obliquus attached on
19
a cathode as oxygen producers for microbial fuel cell (MFC) operation. International Journal of
20
Hydrogen Energy 39(19), 10275-10283.
21
Kondaveeti, S., Choi, K., Kakarla, R. and Min, B. (2014) Microalgae Scenedesmus obliquus as
22
renewable biomass feedstock for electricity generation in microbial fuel cells (MFCs). Frontiers
23
of Environmental Science & Engineering 8(5), 784-791.
AC C
EP
TE D
M AN U
SC
RI PT
1
19
ACCEPTED MANUSCRIPT
Kondaveeti, S. and Min, B. (2013) Nitrate reduction with biotic and abiotic cathodes at various
2
cell voltages in bioelectrochemical denitrification system. Bioprocess and Biosystems
3
Engineering 36(2), 231-238.
4
Logan, B.E., Call, D., Cheng, S., Hamelers, H.V.M., Sleutels, T.H.J.A., Jeremiasse, A.W. and
5
Rozendal, R.A. (2008) Microbial Electrolysis Cells for High Yield Hydrogen Gas Production
6
from Organic Matter. Environmental Science & Technology 42(23), 8630-8640.
7
Lu, K.-M. and Li, S.-Y. (2014) An integrated in situ extraction-gas stripping process for
8
Acetone–Butanol–Ethanol (ABE) fermentation. Journal of the Taiwan Institute of Chemical
9
Engineers 45(5), 2106-2110.
M AN U
SC
RI PT
1
Marshall, C.W., Ross, D.E., Fichot, E.B., Norman, R.S. and May, H.D. (2012) Electrosynthesis
11
of Commodity Chemicals by an Autotrophic Microbial Community. Applied and Environmental
12
Microbiology 78(23), 8412-8420.
13
Merzougui, A., Hasseine, A., Kabouche, A. and Korichi, M. (2011) LLE for the extraction of
14
alcohol from aqueous solutions with diethyl ether and dichloromethane at 293.15K, parameter
15
estimation using a hybrid genetic based approach. Fluid Phase Equilibria 309(2), 161-167.
16
Moon, J.M., Sanath, K. and Booki, M. (2014) Evaluation of low-cost separators for increased
17
power generation in single
18
Fuel Cells.
19
Müller, V. (2001) eLS, John Wiley & Sons, Ltd.
20
Narendranath, N.V. and Power, R. (2005) Relationship between pH and Medium Dissolved
21
Solids in Terms of Growth and Metabolism of Lactobacilli and Saccharomyces cerevisiae during
22
Ethanol Production. Applied and Environmental Microbiology 71(5), 2239-2243.
EP
TE D
10
AC C
chamber microbial fuel cells with membrane electrode assembly.
20
ACCEPTED MANUSCRIPT
Nevin, K.P., Woodard, T.L., Franks, A.E., Summers, Z.M. and Lovley, D.R. (2010) Microbial
2
Electrosynthesis: Feeding Microbes Electricity To Convert Carbon Dioxide and Water to
3
Multicarbon Extracellular Organic Compounds. mBio 1(2).
4
Park, D.H. and Zeikus, J.G. (1999) Utilization of Electrically Reduced Neutral Red by
5
Actinobacillus succinogenes: Physiological Function of Neutral Red in Membrane-Driven
6
Fumarate Reduction and Energy Conservation. Journal of Bacteriology 181(8), 2403-2410.
7
Park, D.H. and Zeikus, J.G. (2000) Electricity Generation in Microbial Fuel Cells Using Neutral
8
Red as an Electronophore. Applied and Environmental Microbiology 66(4), 1292-1297.
9
Rabaey, K. and Rozendal, R.A. (2010) Microbial electrosynthesis — revisiting the electrical
M AN U
SC
RI PT
1
route for microbial production. Nat Rev Micro 8(10), 706-716.
11
Raghavulu, S.V., Babu, P.S., Goud, R.K., Subhash, G.V., Srikanth, S. and Mohan, S.V. (2012)
12
Bioaugmentation of an electrochemically active strain to enhance the electron discharge of
13
mixed culture: process evaluation through electro-kinetic analysis. RSC Advances 2(2), 677-688.
14
Sharma, M., Aryal, N., Sarma, P.M., Vanbroekhoven, K., Lal, B., Benetton, X.D. and Pant, D.
15
(2013) Bioelectrocatalyzed reduction of acetic and butyric acids via direct electron transfer using
16
a mixed culture of sulfate-reducers drives electrosynthesis of alcohols and acetone. Chemical
17
Communications 49(58), 6495-6497.
18
Sharma, M., Varanasi, J.L., Jain, P., Dureja, P., Lal, B., Dominguez-Benetton, X., Pant, D. and
19
Sarma, P.M. (2014) Influence of headspace composition on product diversity by sulphate
20
reducing bacteria biocathode. Bioresource Technology 165(0), 365-371.
21
Spirito, C.M., Richter, H., Rabaey, K., Stams, A.J.M. and Angenent, L.T. (2014) Chain
22
elongation in anaerobic reactor microbiomes to recover resources from waste. Current Opinion
23
in Biotechnology 27(0), 115-122.
AC C
EP
TE D
10
21
ACCEPTED MANUSCRIPT
1
Srikanth, S., Maesen, M., Dominguez-Benetton, X., Vanbroekhoven, K. and Pant, D. (2014)
2
Enzymatic
3
bioelectrochemical system (BES). Bioresource Technology 165(0), 350-354.
4
Steinbusch, K.J.J., Hamelers, H.V.M., Schaap, J.D., Kampman, C. and Buisman, C.J.N. (2009)
5
Bioelectrochemical Ethanol Production through Mediated Acetate Reduction by Mixed Cultures.
6
Environmental Science & Technology 44(1), 513-517.
7
Venkateswar Reddy, M., Amulya, K., Rohit, M.V., Sarma, P.N. and Venkata Mohan, S. (2014)
8
Valorization of fatty acid waste for bioplastics production using Bacillus tequilensis: Integration
9
with dark-fermentative hydrogen production process. International Journal of Hydrogen Energy
formate
through
CO2
sequestration/reduction
in
a
RI PT
of
M AN U
SC
electrosynthesis
39(14), 7616-7626.
11
Wu, H., Chen, X.-P., Liu, G.-P., Jiang, M., Guo, T., Jin, W.-Q., Wei, P. and Zhu, D.-W. (2012)
12
Acetone–butanol–ethanol (ABE) fermentation using Clostridium acetobutylicum XY16 and in
13
situ recovery by PDMS/ceramic composite membrane. Bioprocess and Biosystems Engineering
14
35(7), 1057-1065.
15
Yarlagadda, V.N., Gupta, A., Dodge, C.J. and Francis, A.J. (2012) Effect of exogenous electron
16
shuttles on growth and fermentative metabolism in Clostridium sp. BC1. Bioresource
17
Technology 108(0), 295-299.
18 19
Figure legends
20
Figure 1: Current generation observed in the bioelectrochemical reduction of anaerobic
21
digestion effluent at various external cell voltages (in the absence and presence of mediator)
22
Figure 2: Bioalcohol (a) generation and biogas (b) concentration after the bioelectrochemical
23
reduction of anaerobic digestion effluent at various applied cell voltages (1.0, 1.5, and 2.0 V)
AC C
EP
TE D
10
22
ACCEPTED MANUSCRIPT
Figure 3: Cyclic voltammetry profile at various concentration of externally-supplemented
2
neutral red mediator
3
Figure 4: Bioalcohol (a) generation and biogas (b) concentration after the bioelectrochemical
4
reduction of anaerobic digestion effluent at various applied cell voltages (1.0, 1.5, and 2.0 V) and
5
in the presence of mediator (neutral red at 1 mM)
6
Figure 5: Distribution of Coulombs in synthesized products after bioelectrochemical reduction
7
in the absence (a) and presence (b) of neutral mediator (1mM)
SC
M AN U
8
9
RI PT
1
Tables:
Table 1: Characteristics of anaerobic digestion (AD) effluent supplemented to the BES reactor in
11
present study.
12
Table 2: Product profiles, current generation and cathode potentials observed in BES operation
13
at various operational conditions
14
Supplementary Data:
15
Figure S1: Current generation (a) and concentration of biofuels (b) observed in the BES reactor
16
with growth media at 1.5 V. (Externally supplemented acetic and butyric acid with similar
17
concentration of AD effluent)
18
Figure S2: Current generations observed in the BES reactor with sterilized wastewater (a) and
19
abiotic control (b).
AC C
EP
TE D
10
23
ACCEPTED MANUSCRIPT
Concentration 6.8 ~7.2 0.91 9.2 7.8 86 8.1 6.9 4.9 ±0.21 0.8 ±0.01
RI PT
Unit mS/cm g/L g/L % g/L g/L g/L g/L
SC
Parameter pH Conductivity Total solids (TS) Volatile solids (VS) VS/ TS TSS VSS TCOD SCOD
Table 1: Characteristics of anaerobic digestive (AD) effluent supplemented to BES reactor in
AC C
EP
TE D
M AN U
present study.
ACCEPTED MANUSCRIPT
Products (g/l) EtOH
MeOH
BuOH
-0.45 -0.68 -0.84 -0.51 -0.69
N/A 0.03 N/A 0.02 0.05
N/A 0.02 0.05 0.02 0.02
N/A 0.05 0.09 0.03 0.07
-0.89
0.05
0.03
-0.72
0.03
0.03
PrOH
Gly
RI PT
Cathode Potential (V, Ag/AgCl)
Ac
Lactic Acid
Formic Acid
Propionic Acid
N/A 0.03 0.06 0.03 0.04
N/A N/A 0.05 N/A N/A
N/A N/A 0.04 N/A N/A
0.39 0.62 0.68 0.59 0.57
0.47 0.34 0.38 0.37 0.38
0.47 N/A N/A N/A N/A
0.13
0.04
0.02
0.03
0.67
0.35
N/A
0.04
0.04
N/A
N/A
-
-
-
SC
Applied Current voltage (mA) (V) BES operation 1.0 -0.48 with anaerobic 1.5 -0.64 digestive effluent 2.0 -0.78 1.0 -0.52 BES operation 1.5 -0.7 with anaerobic digestive effluent 2.0 -1.1 and mediator Growth Media with Acetic & Butyric 1.5 -0.78 Acid
M AN U
Operation type
TE D
N/A –Not available; EtOH-Ethanol; MeOH-Methanol; BuOH-Butanol; PrOH-Proponal; Gly- Glycerol; Ac- Acetone
AC C
EP
Table 2: Product profiles, current generation and cathode potentials observed in BES operation at various operational conditions
ACCEPTED MANUSCRIPT
AC C
EP
TE D
M AN U
SC
RI PT
Graphical Abstract
ACCEPTED MANUSCRIPT
Fig. 1
2.0 V
1.5 V
1.0V
1.5 V
2.0 V
TE D
Without Mediator
M AN U
SC
RI PT
1.0 V
With Neutral red
AC C
EP
Fig. 1: Current generation observed in bioelectrochemical reduction of anaerobic digestion effluent at various external cell voltages.
ACCEPTED MANUSCRIPT
AC C
EP
TE D
M AN U
SC
RI PT
Fig. 2
Fig. 2: Bioalcohol (a) and biogas (b) concentration after bioelectrochemical reduction of anaerobic digestion effluent at different applied cell voltages (1.0, 1.5, and 2.0V)
ACCEPTED MANUSCRIPT
M AN U
SC
RI PT
Fig. 3
AC C
EP
TE D
Fig. 3: Cyclic voltammetry profile at various concentration of externally supplemented neutral red mediator
ACCEPTED MANUSCRIPT
AC C
EP
TE D
M AN U
SC
RI PT
Fig. 4
Fig. 4: Bioalcohol (a) and biogas (b) concentration after bioelectrochemical reduction of anaerobic digestion effluent at different applied cell voltages (1.0, 1.5, and 2.0V) and in the presence of mediator (neutral red at 1 mM)
ACCEPTED MANUSCRIPT
Fig. 5
RI PT SC M AN U TE D EP AC C
With Neutral red
B
Total Coulombs(C)
Coulombs distributed in products(C)
A Total Coulombs(C)
Coulombs distributed in products(C)
Without mediator
Fig. 5: Distribution of Coulombs in synthesized products after bioelectrochemical reduction in absence (a) and presence(b) of neutral red mediator (1 mM)
ACCEPTED MANUSCRIPT
Highlights: •
Anaerobic digestion effluent were used for biofuel production via bioelectrochemical reduction Various forms of bioalcohols and biogases were recovered from anaerobic digestion
RI PT
•
effluent •
The main bioalcohols in bioelectrochemical reduction were butanol, ethanol, and
Supplementation of mediator to the system enhanced reductive current and biofuels
EP
TE D
M AN U
production
AC C
•
SC
proponal. .
ACCEPTED MANUSCRIPT
Fig.S1
EP
TE D
B
AC C
Bioalcohol Concentration (g/l)
M AN U
SC
RI PT
A
Fig. S1: Current generation (a) and concentration of biofuels (b) observed in BES reactor with growth media at 1.5 V. (Externally supplemented acetic and butyric acid with similar concentration of AD effluent)
ACCEPTED MANUSCRIPT
RI PT
Fig.S2
1.0 Volt
EP
TE D
M AN U
SC
1.5 Volt
1.5 Volt
AC C
1.0 Volt
Fig. S2: Current generations observed in bioelectrochemcal cell at various applied voltage with sterilized wastewater (a) and abiotic control (b).