- Email: [email protected]
Corrigendum to “Microstructure evolution and mechanical properties of friction stir welding super-austenitic stainless steel S32654” [Mater. Des. 118 (2017) 207-217]
Materials and Design 121 (2017) 261
Contents lists available at ScienceDirect
Materials and Design journal homepage: www.elsevier.com/locate/matdes
Corrigendum
Corrigendum to “Microstructure evolution and mechanical properties of friction stir welding super-austenitic stainless steel S32654” [Mater. Des. 118 (2017) 207-217] Huabing Li a,⁎, Shouxing Yang a, Shucai Zhang a,⁎, Binbin Zhang a, Zhouhua Jiang a, Hao Feng a, Peide Han b, Jizhong Li c a b c
School of Metallurgy, Northeastern University, Shenyang 110819, China College of Materials Science and Engineering, Taiyuan University of Technology, Taiyuan 030024, China Guangdong Welding Institute (China-Ukraine E. O. Paton Institute of Welding), Guangzhou 510650, China
The authors regret to inform that Fig. 7 is not correct and same as Fig. 6. The correct form of Fig. 7 is as follows:
Fig. 7. (a) EBSD image quality maps, (b) grain boundary maps and (c) misorientation angle distributions for the BM (top) and the SZ of FSW at rotational speeds of 300 rpm (middle) and 400 rpm (bottom). LABs are depicted as pink and blue lines, HABs are marked by black lines on the grain boundary maps, respectively. (For interpretation of the references to colour in this figure legend, the reader is referred to the web version of this article.)
Author would like to apologize for the inconvenience caused. DOI of original article: http://dx.doi.org/10.1016/j.matdes.2017.01.034. ⁎ Corresponding authors. E-mail addresses: [email protected] (H. Li), [email protected] (S. Zhang).
http://dx.doi.org/10.1016/j.matdes.2017.02.051 0264-1275/© 2017 Elsevier Ltd. All rights reserved.
Contents lists available at ScienceDirect
Materials and Design journal homepage: www.elsevier.com/locate/matdes
Corrigendum
Corrigendum to “Microstructure evolution and mechanical properties of friction stir welding super-austenitic stainless steel S32654” [Mater. Des. 118 (2017) 207-217] Huabing Li a,⁎, Shouxing Yang a, Shucai Zhang a,⁎, Binbin Zhang a, Zhouhua Jiang a, Hao Feng a, Peide Han b, Jizhong Li c a b c
School of Metallurgy, Northeastern University, Shenyang 110819, China College of Materials Science and Engineering, Taiyuan University of Technology, Taiyuan 030024, China Guangdong Welding Institute (China-Ukraine E. O. Paton Institute of Welding), Guangzhou 510650, China
The authors regret to inform that Fig. 7 is not correct and same as Fig. 6. The correct form of Fig. 7 is as follows:
Fig. 7. (a) EBSD image quality maps, (b) grain boundary maps and (c) misorientation angle distributions for the BM (top) and the SZ of FSW at rotational speeds of 300 rpm (middle) and 400 rpm (bottom). LABs are depicted as pink and blue lines, HABs are marked by black lines on the grain boundary maps, respectively. (For interpretation of the references to colour in this figure legend, the reader is referred to the web version of this article.)
Author would like to apologize for the inconvenience caused. DOI of original article: http://dx.doi.org/10.1016/j.matdes.2017.01.034. ⁎ Corresponding authors. E-mail addresses: [email protected] (H. Li), [email protected] (S. Zhang).
http://dx.doi.org/10.1016/j.matdes.2017.02.051 0264-1275/© 2017 Elsevier Ltd. All rights reserved.