Journal Pre-proof Geological and geophysical features of and controls on occurrence and accumulation of gas hydrates in the first offshore gas-hydrate production test region in the Shenhu area, Northern South China Sea Wei Zhang, Jinqiang Liang, Jiangong Wei, Jing'an Lu, Pibo Su, Lin Lin, Wei Huang, Yiqun Guo, Wei Deng, Xiaolu Yang, Zhifeng Wan PII:
S0264-8172(19)30645-2
DOI:
https://doi.org/10.1016/j.marpetgeo.2019.104191
Reference:
JMPG 104191
To appear in:
Marine and Petroleum Geology
Received Date: 15 May 2019 Revised Date:
13 December 2019
Accepted Date: 14 December 2019
Please cite this article as: Zhang, W., Liang, J., Wei, J., Lu, Jing'., Su, P., Lin, L., Huang, W., Guo, Y., Deng, W., Yang, X., Wan, Z., Geological and geophysical features of and controls on occurrence and accumulation of gas hydrates in the first offshore gas-hydrate production test region in the Shenhu area, Northern South China Sea, Marine and Petroleum Geology (2020), doi: https://doi.org/10.1016/ j.marpetgeo.2019.104191. This is a PDF file of an article that has undergone enhancements after acceptance, such as the addition of a cover page and metadata, and formatting for readability, but it is not yet the definitive version of record. This version will undergo additional copyediting, typesetting and review before it is published in its final form, but we are providing this version to give early visibility of the article. Please note that, during the production process, errors may be discovered which could affect the content, and all legal disclaimers that apply to the journal pertain. © 2019 Published by Elsevier Ltd.
1
Geological and geophysical features of and controls on occurrence and accumulation of gas hydrates in the
2
first offshore gas-hydrate production test region in the Shenhu area, northern South China Sea
3 4
Wei Zhanga,b,c, Jinqiang Liang a,c, Jiangong Weia,c*, Jing’an Lua, Pibo Sua,c, Lin Lina, Wei Huanga,c, Yiqun Guoa, Wei
5
Denga, Xiaolu Yangb, Zhifeng Wanb*
6 7
a
MNR Key Laboratory of Marine Mineral Resources, Guangzhou Marine Geological Survey, Ministry of
Natural Resources, Guangzhou 510075, China
8
b
School of Marine Sciences, Sun Yat-sen University, Zhuhai, 519000, China
9
c
Southern Marine Science and Engineering Guangdong Laboratory, Guangzhou,511458, China
10 11
Abstract: Integrated three-dimensional seismic, logging, sediment cores, and geochemical testing data were
12
collected from Guangzhou Marine Geological Survey 3 and 4 hydrate drilling expeditions and used in this study for
13
a comprehensive investigation of the geological and geophysical features and accumulation mechanism of hydrates
14
in the first offshore gas-hydrate production test region (GHPTR) in the Shenhu area of the South China Sea.
15
Seismic signatures indicative of disseminated‐hydrates and free gas include the bottom simulating reflector (BSR),
16
gas chimney, and mud diapirs associated with enhanced seismic reflections, acoustic blanking, masking, and chaotic
17
appearance have been observed. The acoustic travel-time responses, density, and compensated neutron three porosity
18
log analysis, high-precision grid tomography inversion analysis, and constrained sparse spike inversion confirm the
*
Corresponding author, E-mail:
[email protected], E-mail:
[email protected]
Wei Zhang and Jinqiang Liang are both regarded as the first author. 1
19
presence of free gas below the gas-hydrate-bearing zone (GHBZ). Free-gas-bearing zones have significantly different
20
p-wave impedances and low-velocity anomalies than the overlying GHBZ and surrounding strata. These anomalous
21
zones are controlled by the structural attitude of the reservoir strata, which are characterized as inter-bedded
22
stratigraphic units. Variations in the type and geological characteristics of the hydrocarbon migration pathways were
23
observed between sites W18 and W19 on the western ridge and sites W11 and W17 on the eastern ridge in the GMGS
24
study area. The efficiency of gas migration in the western ridge may be higher than that in the eastern ridge, resulting
25
in variations in hydrate gas types, thickness of the GHBZ, and gas migration flux and accumulation. Except for site
26
W11, hydrates were recovered below the structure I inferred BSR at sites W17, W18, and W19. The gas-hydrate
27
stability zone calculations reveal that the structure I hydrate stability zone differs from the BSR depth and is
28
generally shallower than the base of the logging anomaly, indicating the coexistence of structure I and II hydrates.
29
The BSR is not indicative of the BGHSZ; it is rather regarded as a transitional indicator of structure I and II gas
30
hydrates in the GHPTR. The appearance of free gas and hydrates below the structure I inferred BSR indicates that
31
the Shenhu area is characterized by a complex hydrate formation and accumulation system resulting from the
32
supply of biogenic and thermogenic gases. Despite fine-grained host sediments predominating the GHPTR, the
33
coupling of favorable conditions including efficient hydrocarbon generation, sufficient gas supply, multiple
34
pathways for gas migration, and relatively high reservoir porosity have led to the development of highly saturated
35
gas-hydrate accumulations within relatively thick sedimentary sections, which demonstrates a significant resource
36
potential.
37 38
Keywords: Gas hydrates; Logging while drilling; Velocity and impedance inversion; Free gas; Migration and accumulation mechanism; Gas-hydrate production; Shenhu area; northern South China Sea
2
39
1. Introduction
40
Gas hydrates are clathrate crystalline compounds composed of natural gas (mainly methane gas) and water
41
molecules under appropriate temperature and pressure conditions (Kvenvolden, 1988). Gas hydrates are widely
42
distributed in deep-water continental slopes with a water depth of more than 300 m and in the permafrost
43
(Kvenvolden, 1993). They have attracted increasing attention around the world and have been considered as a
44
potential clean energy source to supplement future energy supplies (Collett, 2002; Collett, 2004; Boswell and
45
Collett, 2006). Because of their significant potential as an environment-friendly energy resource and positive
46
impacts on the greenhouse effect and marine ecological systems, the governments of the United States, Canada,
47
Japan, South Korea, and India as well as many research institutes have invested in the exploration and development
48
of gas hydrates. Many gas-hydrate drillings and test productions have been undertaken on land in permafrost
49
regions and continental slopes. These tests achieved significant breakthroughs (Tréhu et al., 2004a; Tréhu et al.,
50
2004b ; Moridis et al., 2004; Dallimore et al., 2005; Dallimore and Collett, 2005; Collett et al., 2008; Anderson et
51
al., 2011; Boswell et al., 2012; Collett et al., 2012; Ryu et al.,2013; Collett et al., 2014; Wang et al., 2014; Fujii et
52
al., 2015; Zhang et al., 2007; Yang et al., 2008; Yang et al., 2015; Zhang et al., 2015; Zhang et al., 2017; Li et al.,
53
2018), and the processes of the exploration and development of gas hydrates and utilization of these resources have
54
been actively promoted.
55
The northern continental slopes of the South China Sea (SCS) (Fig. 1A) possess good geological,
56
geomorphological, and geochemical conditions for the formation and accumulation of gas hydrates (Zhang et al.,
57
2002; Wu et al., 2005; Wang et al., 2006; Yang et al., 2008; Wu et al., 2009; Wu et al., 2010; Wu et al., 2011; Wang
58
et al., 2014; Zhang et al., 2015; Sha et al., 2015; Yang et al., 2017a; Yang et al., 2017b; Yang et al., 2017c; Yang et 3
59
al., 2017d; Zhang et al., 2017; Zhang et al., 2018a; Zhang et al., 2018b; Zhong et al., 2017; Wei et al., 2018; Ye et
60
al., 2019; Wei et al., 2019; Zhang et al., 2019). Regional marine geological surveys and oil and gas exploration
61
research indicate that there are abundant gas-hydrate resources in the northern continental slope of the SCS (Zhang
62
et al., 2002; Wu et al., 2005; Wu et al., 2010; Wang et al., 2014; Zhang et al., 2015; Sha et al., 2015; Yang et al.,
63
2015; Zhang et al., 2017; Wang et al., 2018; Su et al., 2018). The Guangzhou Marine Geological Survey (GMGS)
64
undertook two gas-hydrate drilling expeditions in the Shenhu area of the northern continental slope of the SCS in
65
2007 and 2015, viz., the GMGS1 and GMGS3 expeditions, to obtain core samples containing gas hydrates, confirm
66
the existence of gas hydrates, explore the formation and accumulation mechanisms of hydrates, and evaluate the
67
hydrate resources in the northern SCS (Zhang et al., 2007; Yang et al., 2008; Yang et al., 2015; Zhang et al., 2017).
68
During these expeditions, eight sites were drilled in the 2007 GMGS1 expedition (Wang et al., 2014; Su et al., 2016),
69
and hydrate samples were obtained at three sites: SH2, SH3, and SH7 (Fig. 1B). Post-drilling research showed that
70
gas hydrates, which were invisible to the naked eye, are distributed within the pores of the clay-dominated sediments
71
at approximately 200 mbsf (meters below seafloor); the morphologies of the gas hydrates are disseminated, and the
72
methane concentration of the hydrate gas components is up to 99.7% (Zhang et al., 2007; Wang et al., 2014; Su et al.,
73
2016). The thickness of the hydrate-bearing layer in the GMGS1 drilling zone is approximately 10-47 m. In addition,
74
the average saturation of the hydrates acquired from the coring sites varies from 20% to 48% (Wang et al., 2014). The
75
GMGS1 expedition was the first time that the GMGS obtained gas-hydrate samples in the SCS. Furthermore, the
76
hydrate geology, geophysics, gas source genetic types, reservoir characteristics, and bioorganic geochemistry were
77
extensively studied after drilling (Wu et al., 2010; Wu et al., 2011; Wang et al., 2014; Su et al., 2016; Wang et al.,
78
2018; Guan et al., 2018; Guan et al., 2019; Fang et al., 2019; Xiong et al., 2019). However, because of the small
79
quantity of drilling boreholes‐and limited areas covered by these boreholes in the GMGS1 expedition, few studies 4
80
have focused on the distribution, factors controlling accumulation, and resource calculation and evaluation of
81
hydrates throughout the Shenhu area (Wu et al., 2010; Wang et al., 2014; Su et al., 2016), which restricts further
82
research on the accumulation mechanism of hydrates and resource evaluation.
83
The GMGS implemented the GMGS3 expedition in the Shenhu area in 2015 to obtain high-quality geophysical
84
logging data and more core samples of the hydrate-bearing layers, evaluate high-saturation hydrate accumulation
85
characteristics and the amount of hydrate resources, and provide a basis for the optimization of the gas-hydrate
86
production test region (GHPTR) in the SCS (Fig. 1B) (Yang et al., 2015). The GMGS3 expedition completed drilling
87
at 19 sites, and 23 wells were drilled. Coring was conducted and hydrate samples were obtained at sites W11, W17,
88
W18, and W19, where the logging-while-drilling (LWD) data indicates significant reserves of gas hydrates. The
89
hydrate saturations at these four sites, which were calculated using the pore-water freshening analysis from chlorinity
90
and mass balance calculations from the pressure cores, were as high as 76%, with an average value of ~20%–40%
91
(Yang et al., 2015; Zhang et al., 2017; Guo et al., 2017; Qian et al., 2018). In addition, the thickness of the main
92
gas-hydrate-bearing zone (GHBZ) was generally up to 10-80 m (Yang et al., 2017b; Yang et al., 2017d). Generally,
93
the thickness and saturation of gas hydrates discovered during the GMGS3 expedition were significantly larger than
94
those discovered during the GMGS1 expedition (Wang et al., 2014; Yang et al., 2015; Su et al., 2016; Guo et al.,
95
2017; Zhang et al., 2017; Yang et al., 2017b).
96
In 2016, the GMGS conducted gas-hydrate drilling (GMGS4) in the Shenhu area again (Fig. 1B). Four deep
97
drilling and coring sites were finished in the vicinity of the coring sites of the GMGS3 expedition (Yang et al., 2017c;
98
Yang et al., 2017d). In addition to recovering gas-hydrate samples with high saturations, hydrate deposits with
99
predicted original in-place gas of more than 100 billion cubic meters were confirmed (China Geological Survey, 5
100
Ministry of Land and Resources, 2016).
101
The geochemical testing results indicate that the compositions of the hydrate gases obtained from the GMGS3
102
and GMGS4 expeditions are methane dominated; its hydrocarbon gas content was generally greater than 93.5%.
103
However, heavier hydrocarbons, viz., ethane, propane, and even butane and pentane, were also detected in several gas
104
samples. These were different from the hydrate gas compositions in the GMGS1 drilling area (Huang et al., 2010; Su
105
et al., 2016; Liu et al., 2017; Li et al., 2019a; Zhang et al., 2019) where the content of heavy hydrocarbons, such as
106
ethane and propane, were extremely low and methane accounted for the vast majority of the total gas content (Huang
107
et al., 2010; Wu et al., 2011; Zhu et al., 2013). Further analysis revealed that the ratio of C1 to C2 in the hydrate gases
108
generally decreased with depth, and there were abrupt changes near the top interface of the hydrate layer, thereby
109
indicating the increase in the contribution of the thermogenic gas with depth (Yang et al., 2015; Zhang et al., 2017;
110
Cong et al., 2018; Zhang et al., 2019). The C1/(C2+C3) versus δ13C1 diagram reveals that most of the hydrate
111
decomposition gas and void gas samples from the gas-hydrate layers at sites W17, W18, and W19 were in the range
112
of mixed gases. The hydrate decomposition gases were primarily within the range of thermogenic gas (Zhang et al.,
113
2019) on the δ13C1 versus δDCH4 genetic type diagram. In addition, the hydrate gas recovered from the first
114
gas-hydrate production test well SHSC-4, which is located near site W17 within the GHPTR, also exhibits a “mixed
115
origin” (Ye et al., 2018), which is similar to the hydrate gas origin of coring sites W11, W17, W18, and W19.
116
Furthermore, the genetic type of hydrate gases obtained from other districts with gas-hydrate occurrences indicates
117
that the origin of the hydrate gas within the GHPTR is different from the hydrate gas from the Krishna Godavari
118
Basin (KG Basin) (Lorenson and Collett, 2018), Ulleung Basin (Choi et al., 2013), and Nankai Trough (Kida et al.,
119
2015), which have an entirely microbial origin. In addition, the origins of the hydrate gas from sites W18 and W19
6
120
are the same as the gas from the Gulf of Mexico (Sassen et al., 2001), i.e., thermogenic origin. In summary, the
121
hydrate gas in the GHPTR has a mixed origin, and both biogenic and thermogenic gases significantly contribute to
122
the formation and accumulation of these gas hydrates (Yang et al., 2015; Zhang et al., 2017; Liu et al., 2017; Cong et
123
al., 2018; Ye et al., 2018; Zhang et al., 2019).
124
Based on the exploration results of the GMGS 1, 3, and 4 expeditions, the GMGS constructed an optimization of
125
the GHPTR in the Shenhu area in the SCS, promoting the success of the first offshore gas-hydrate production test in
126
China in 2017 (Li et al., 2018; Ye et al., 2018) implemented after the offshore gas-hydrate production tests in the
127
Nankai Trough in 2013 and 2017 (Konno et al., 2017; Yamamoto et al., 2019). The first successful offshore
128
experimental production of hydrates in the Shenhu area indicates that the GHPTR discussed in this paper is likely
129
to be a favorable target for large-scale development of gas hydrates in the SCS (Chen et al., 2018). However, prior
130
to the GMGS drilling, the general consensus was that disseminated gas hydrates in fine-grained sediments were likely
131
accumulated with very low saturations and limited thicknesses in the Shenhu area. However, the GMGS expeditions
132
have confirmed that the accumulation does achieve unexpected saturation and thickness in the GHPTR. In addition,
133
the gas hydrates have been discovered below the bottom simulating reflector (BSR) (Liang et al., 2017; Wei et al.,
134
2018), and free gas has also been found to coexist with gas hydrates (Qian et al., 2018). However, the distribution of
135
gas hydrates and associated free gases and their controlling factors are still unknown. Therefore, the factors in the
136
entire gas-hydrate petroleum system need further investigation. Furthermore, although the geological and
137
geophysical
138
distribution characteristics of the Shenhu area have been studied by many previous researchers (Wang et al., 2014;
139
Yang et al., 2015; Su et al., 2016; Guo et al., 2017; Zhang et al., 2017; Yang et al., 2017b; Qian et al., 2018; Wang
characteristics
of
the
hydrates,
geochemical
7
features
of
hydrate
gases,
and
hydrate
140
et al., 2018; Li et al., 2019a; Zhang et al., 2019; Xiong et al., 2019), these studies were aimed at a certain scientific
141
problem or a certain aspect of research. Therefore,‐the paucity of research on the geological and geophysical features
142
of the indicators of gas-hydrate accumulation and hydrocarbon migration in the GHPTR and the lack of a
143
systematic understanding of the accumulation mechanism of widespread gas hydrates with high saturations as well as
144
associated free gas also pose difficulties to our understanding of the distribution and accumulation of gas hydrates
145
and future optimization of hydrate production sites in the SCS.
146
Therefore, we selected the GHPTR in the Shenhu area on the northern continental slope of the SCS as the study
147
area and focused on the hydrate deep drilling and coring sites within this region. Based on the comprehensive
148
interpretation and analyses of the cores, logging data, 3D seismic data, and geochemical testing data, this paper aims
149
to: (1) identify the seismic and logging indicators of hydrocarbon migration and hydrate accumulation with high
150
saturations and large thicknesses; (2) characterize the coexistence and distribution of gas hydrates and their
151
associated free gases within difference regions; (3) discuss the inconsistent distribution between the BSR, base of
152
gas-hydrate stability zone (BGHSZ), and gas hydrates; and (4) analyze the reservoir characteristics and their impact
153
on the differential accumulation of gas hydrates with variable saturations and thicknesses. This paper can be a
154
significant reference for the selection of favorable exploration areas and subsequent drilling sites in the SCS,
155
evaluation of hydrate resource potential, and research on hydrate production. In addition, it can be of significance for
156
further research on the hydrate accumulation mechanism and hydrate production in other areas with similar
157
geological settings around the world.
158
8
159
2. Regional geological background and petroleum system
160
The study area of the GHPTR in the Shenhu area is within the southern part of the Pearl River Mouth Basin
161
(PRMB) and is located on the vast continental shelf and the continental slope area between the South China continent,
162
Hainan Island, and Taiwan Island (Fig. 1A). The PRMB is approximately 800 km long and 300 km wide, with a basin
163
area of approximately 20 × 104 km2. The basin water depth is 50-2000 m. It is the largest petroliferous basin on the
164
northern slope of the SCS.
165
The PRMB possesses the characteristics of both passive and active continental margins, resulting in a complex
166
regional geological background (Li and Rao, 1994; Dong et al., 2009). During the Cenozoic, many regional tectonic
167
movements—including the Shenhu, Zhuqiong, SCS, Baiyun, and Dongsha events—occurred in succession (Li, 1993;
168
Pang et al., 2008) (Fig. 2), resulting in three groups of normal faults with NE, NW, and NWW strikes controlling the
169
distribution of the modern tectonic units in the PRMB (Pang et al., 2008; He et al., 2012; Zhong et al., 2014). The
170
tectonic evolution of the Cenozoic basin in this area can be divided into two stages: an early rifting stage in the
171
Paleogene and a late depression stage in the Neogene (Li and Rao, 1994; Zhong, 1994) (Fig. 2). In the Paleocene,
172
Eocene, and Early Oligocene, there was a half graben-like or graben-shaped rift basin that deposited continental
173
strata composed of the Paleocene Shenhu Formation, Eocene Wenchang Formation, and Lower Oligocene Enping
174
Formation (Mi et al., 2008). The PRMB has gradually transitioned into the depression stage since the Upper
175
Oligocene and has deposited Late Oligocene Zhuhai Formation neritic strata and Miocene-Pliocene neritic-abyssal
176
strata. In addition, there is a prominent unconformity between the Lower Oligocene and Upper Oligocene, which are
177
separated by the T6 interface (Fig. 2) (Shao et al., 2008; Xie et al., 2013; Shi et al., 2014).
178
The Shenhu area is adjacent to the center of the southern deep-water Baiyun Sag in the PRMB (Fig. 1B). 9
179
Petroleum exploration has confirmed the presence of sufficient natural gas resources in the Baiyun Sag area. A
180
significant number of gas fields, including the LW-3-1, LH 19-1, and PY 35-1, have been discovered around the
181
GMGS gas-hydrate drilling sites in this area (Shi et al., 2009a; He et al., 2009; Shi et al., 2010; He et al., 2012;
182
Zhang et al., 2019). The Paleogene Eocene Wenchang Formation and Oligocene Enping Formation were identified
183
as the main mature to highly mature source rocks, which generate abundant thermogenic hydrocarbons (Shi et al.,
184
2014; Zhang et al., 2014; Li et al., 2015). Although the organic material deposited in the Zhujiang and Hanjiang
185
formations was in the immature-low mature stage, the formations could act as source rocks and produce significant
186
amounts of biogenic gases (Fu et al., 2007; He et al., 2013; Su et al., 2018). In addition, both thermogenic gas from
187
the deep strata and biogenic gas from the shallow strata provided sufficient hydrocarbons for the formation of gas
188
hydrates in the Shenhu area (Wang et al., 2014; Yang et al., 2017b; Zhang et al., 2017; Su et al., 2018; Zhang et al.,
189
2019).
190
Based on the geological characteristics of the hydrocarbon accumulation in the Baiyun Sag, the deep-seated
191
thermogenic gas mostly migrated along continuous sand bodies extending into the Baiyun Sag and along regional
192
unconformities, such as T7 and T6 (Fig. 2) (Yu et al., 2007; Hou et al., 2008; Shi et al., 2010; Lin and Shi, 2014). In
193
addition, the normal faults, mud diapirs, and gas chimneys could also act as vertical pathways for oil and gas
194
migrating from the deep strata to shallow strata (Shi et al., 2009a; Shi et al., 2009b; Liu et al., 2011). The
195
Neotectonic movement induced plastic flow of the thick overpressure mud shale in the Paleogene strata, forming a
196
large-scale mud diapir belt, which resulted in the wide distribution of diapirs and gas chimneys (2009b). The upward
197
intrusion of diapirs started from the Early Neogene and is still continuing. This has resulted in overlying anticlines at
198
different depths as well as high-angle faults and vertical fracture systems. These structures constitute important
10
199
pathways for the migration of the deep and shallow gas-bearing fluids that provide sufficient natural gas for the
200
formation of gas hydrates in the Shenhu area (Shi et al., 2009a; Shi et al 2009b; Su et al., 2016).
201
The gas-hydrate drilling zones of the GMGS 1, 3, and 4 expeditions are located in the transition area from the
202
continental slope to the abyssal plain, and the GMGS 3 and 4 drilling areas are adjacent to the eastern part of the
203
GMGS1 drilling area (Fig. 1B). The GHPTR is located in the southwestern part of the GMGS 3 and 4 drilling areas,
204
and the drilling and coring sites are located in the structural highs and marginal parts of the two seafloor ridges (the
205
western and eastern ridges) (Figs. 1B, 3). The seafloor in this area is relatively flat, with an average slope of
206
approximately 3°. The depth of the water deepens from ~500 m to more than 1,700 m, and the landforms in the
207
northern part of the Shenhu area are relatively steep. From west to east, there are 17 submarine trenches striking
208
nearly NS, which alternate with submarine ridges (Su et al., 2019). The southern terrain is flat and gradually
209
transitions to an abyssal plains to the south. The research area mostly consists of landforms, such as seamounts,
210
submarine canyons, scour channels, and erosion trenches (Wang et al., 2014; Su et al., 2017; Zhang et al., 2017).
211
The seafloor temperature of the Shenhu area is between 3 and 6 °C, and the geothermal gradient is between
212
~45 °C/km and ~67 °C/km, which satisfies the temperature conditions for hydrate formation. The depth of
213
gas-hydrate distribution generally varies from ~150 to ~400 mbsf (Wu et al., 2010; Liang et al., 2014; Zhang et al.,
214
2017).
215
3 Data and methods
216
3.1 Seismic and LWD data
217
The GMGS3 and 4 drilling areas are located within the pseudo-3D seismic survey in the Shenhu area. The
218
seismic volume, covering 17.1 km × 9.5 km, was shot by the GMGS from 2006 to 2009. The intervals of the inline 11
219
and the crossline of the seismic data were 12.5 m and 25 m, respectively; and the sampling interval was 1 ms. The
220
effective frequency band width of the seismic data is 5-85 Hz, and the main frequency is about 58 Hz. The seismic
221
data has a high quality after it was processed by fidelity, amplitude-preservation, and pre-stacking depth migration.
222
The interpretation of the seismic data was performed using Geoframe 4.5.
223
Twenty-three boreholes were drilled spanning over nineteen drilling sites during the GMGS3 expedition (Yang
224
et al., 2015; Yang et al., 2017b). The caliper log, gamma ray log, drilling rate, resistivity, density, neutron log, and
225
acoustic log were monitored in real time during the LWD process. Four sites (W11, W17, W18, and W19) (Fig. 1B)
226
were cored based on the logging response characteristics of the LWD data collected from the pilot hole (Wang et al.,
227
2014), which were targeted from the seafloor to 50–100 m below the BSR observed on the seismic profile. The other
228
15 sites also showed indications for the presence of gas hydrate in the LWD; however, no cores were collected from
229
these sites according to the coring plan. In addition to the LWD programs, drilling and coring activities were also
230
performed at four other sites (W07, SC01, SC02, and SC03) during the GMGS4 expedition (Yang et al., 2017c; Yang
231
et al., 2017d). The porosities and permeabilities of gas-hydrate reservoirs were calculated by the Schlumberger based
232
on the LWD data, the results are reported in Table 1. These results were used to explore the relationship between the
233
quality of the reservoirs and gas-hydrate accumulation. To further analyze the relationship between the gas-hydrate or
234
free gas distribution and the seismic reflection amplitude, polarity, and so on, synthetic seismograms were
235
constructed based on the LWD and seismic data acquired from the drilling and coring sites. Because sites SC01,
236
SC02, and SC03 were near sites W18, W19, and W11, respectively (Fig. 1B), the corresponding sites had similar
237
gas-hydrate geological occurrences and distribution features owing to the short distance between the sites (Yang et al.,
238
2017c; Yang et al., 2017d) (Figs. 1B, 3). Therefore, in this study, we primarily discuss sites W11, W17, W18, and
12
239
W19 within the GHPTR.
240 241
3.2 Core samples and grain size analysis
242
The drilling sites in GMGS 3 and 4 were conventionally cored using spaced out spot cores with pressure
243
coring tools, which were also used in the GMGS 1 and 2 gas-hydrate drilling expeditions (Wang et al., 2014; Sha et
244
al., 2015; Yang et al., 2017d). Owing to the limited time allotted for the GMGS 3 expedition, the boreholes could
245
not be cored continuously. The initial coring and testing plan for each site was generated by picking coring targets
246
from the LWD logs, which indicated the presence of gas hydrates. The temperature profile was determined from the
247
temperature measurements using the Wison EP temperature/cone penetrometer probe. The total footage of the
248
coring was about 975 m, and the coring recovery rate was 88.32%. In addition to the conventional cores
249
(non-pressured cores) recovered from above and below the GHBZ, 36 m of pressure core was recovered, with a
250
recovery rate of 64% of the pressure cored intervals.
251
The pressured and conventional cores were handled suitably with different methods in the field. The
252
conventional cores were sent to the onboard laboratory immediately upon recovery for infrared thermal imaging
253
using a forward looking infrared camera. If gas-hydrate-bearing segments were recognized on the infrared thermal
254
images, they were cut and preserved in liquid nitrogen tanks for further onshore analyses. The pressured cores were
255
sent to the onboard pressured core laboratory for depressurization experiments using the Automated Depressure
256
System (ADS) (Yang et al., 2017d). After the recovered cores were transported to the onshore GMGS lab, systematic
257
core observations and descriptions were undertaken and detailed sedimentology records were prepared. To
258
understand the characteristics of the lithologies of hydrate reservoirs, measurements of the grain sizes of the core 13
259
sediments were performed onshore using the Mastersizer 2000 Laser Grain Size Analyzer (SYE209) in the
260
Department of Testing in the GMGS. In addition, abundant foraminifera fossils were found within the core sediments
261
during the core observation and description, and foraminifera identification was done using the Zeiss Discovery,
262
V20/LEICA.MI165C Binocular stereo microscope. X-ray diffraction for the whole rock analysis was also performed
263
using the D/max-2500 18-kw high-power powder diffractometer in the GMGS.
264 265
3.3 Free-gas identification method
266
Free gases are generally distributed under the GHBZ and accumulate within reservoirs with relatively high
267
porosities. Four methods were used to identify the distribution of free gases based on the geophysical
268
characteristics of the GHPTR.
269
(1) Because of the distinct difference in the impedance values of the gas reservoir and surrounding strata,
270
enhanced reflections are usually seen below the BSR in seismic profiles (Vanneste et al., 2001; Kumar et al., 2018).
271
Therefore, the distribution of the free-gas layers can be determined by tracing the strong reflection characteristics
272
below the hydrate layers. In addition, there is a strong difference in impedance values between the GHBZ and
273
underlying free gas. Using the constrained sparse spike inversion (CSSI) method in the software Jason, under the
274
control of the GHBZ and BSR, the entire logging data for the hydrate orebody in the study area was used to
275
complete the post-stacking CSSI processing and obtain the p-wave impedance, which revealed the distinct
276
distribution of the GHBZ and underlying free gas at the four coring sites.
277 278
(2) The acoustic travel-time difference, density, and compensation neutron three porosity log intersection method were used to identify and interpret the GHBZ and the free-gas-bearing zones (FGBZ) in the GHPTR. 14
279
(3) Because the FGBZ usually has the electrical characteristics of "excavation effect" with a low density and
280
high acoustic time difference, it generally exhibits a remarkable low-velocity feature, which is significantly
281
different from the background velocity of the surrounding strata without hydrocarbon accumulation. Thus, the
282
extent of the free gas under the GHBZ can be determined by tracing the low-velocity anomalies (Fohrmann and
283
Pecher, 2012; Cordero et al., 2016). Based on the pre-stacking depth migration processing of the seismic data,
284
accurate shallow strata velocity volumes can be obtained using high-precision grid tomography inversion (Xue et
285
al., 2017; Li et al., 2019b). Subsequently, the tracing of the distribution of free gas can be implemented.
286
(4) Because of the strong attenuation of the high-frequency components of seismic waves in gas-bearing strata,
287
the seismic attributes are usually characterized by a low instantaneous frequency. Therefore, the entrapment area of
288
the free gas below the BSR can be roughly judged by extracting and analyzing the seismic instantaneous frequency
289
attributes (Coren et al., 2001; Satyavani et al., 2005; Shankar et al., 2014; Kumar et al., 2018).
290 291
3.4 Gas-hydrate stability zone modeling
292
Based on the in situ measured temperature (Table 2) and geochemical data for the hydrate gases acquired from
293
sites W11, W17, W18, and W19 (Zhang et al., 2019), the gas-hydrate stability curves of each site were calculated
294
using the CSMHYD program (Sloan, 1998). The geothermal gradient of each site was calculated using the in situ
295
measured temperature (Table 2). Subsequently, the BGHSZ was obtained by identifying the intersection of the
296
gas-hydrate stability curves with the geothermal gradient (Liang et al., 2017). In addition, to verify the possible
297
presence of gas hydrates below the BSR, the BGHSZ was calculated using different gas compositions (100% C1, 99%
298
C1 + 0.5% C2 + 0.5% C3, and 95% C1 + 2.5% C2 + 2.5% C3) and was compared with the BSR, logging anomaly
15
299
distribution intervals, and pore-water anomalies tested within the GHPTR (Cong et al., 2018; Guo et al., 2017;
300
Yang et al., 2017c; Zhang et al., 2017). Structure I (SI) gas hydrates contain gas, with 100% methane gas; whereas
301
the presence of C2+ hydrocarbons in the hydrate cage results in the formation of structure II (SII) gas hydrates.
302
Therefore, the BGHSZ calculated with 100% methane corresponds to the BGHSZ of SI hydrates, and the BGHSZ
303
calculated with the other gas compositions used in this study corresponds to the BGHSZ of SII hydrates. If the
304
logging curves and core sediments show indicators of gas hydrates and pore-water anomalies occur below the BSR
305
or calculated SI gas-hydrate BGHSZ, gas hydrates will be accumulated below the BSR and SI and SII hydrates may
306
coexist at the site (Paganoni et al., 2016; Liang et al., 2017; Zhang et al., 2019; Wei et al., 2019).
307
308
4. Results
309
4.1 Geological occurrence of gas hydrates
310
In situ measurements and coring were performed at sites W11, W17, W18, and W19 (Figs. 3–7), and samples of
311
gas hydrates, which mainly occur in fine-grained clayey silt, were obtained. They were mostly disseminated hydrates,
312
which were not visible to the naked eye. Some of the hydrates were of the fracture-filled type (Yang et al., 2015; Yang
313
et al., 2017b, d). The occurrence characteristics of the drilling and coring hydrates at each site are given in Table 1
314
and Figures 8–11.
315
4.1.1 Site W11
316
Site W11 is located on the lower part of the eastern submarine ridge in the southeastern corner of the drilling area
317
(Figs. 1B, 3, 4 . The water depth was ~1310 m; the actual drilling depth was ~222 mbsf; and the geothermal gradient 16
318
was 5.46 °C/100 m. The pilot hole LWD resistivity curves exhibit four sections of anomalously high values between
319
112 mbsf and 201.6 mbsf, and the layer thickness is approximately 90 m (Fig. 8A). The actual coring indicates that
320
the depth of the gas-hydrate occurrences is consistent with resistivity anomalies (Fig. 9A). The core data from this
321
site reveals that gas hydrates occur over a 72 m interval from 116.5 mbsf to 192.5 mbsf. The gas hydrates
322
are dispersed within the pores of the sediments and are not visible to the naked eye. One distinct characteristic
323
observed is that the hydrates in the cores obtained from the strata at 116–117 mbsf and 120–121 mbsf are decomposed,
324
which resulted in inflation and creation of cavities in cores (Figs. 11A, 11B). Because of the dissociation of the
325
hydrates, the sediments exhibit porridge-like characteristics at depths of 139–142 mbsf (Fig. 11C). In addition, the
326
infrared thermal imaging of the cores obtained from site W11 exhibits significant negative thermal anomalies in the
327
GHBZ (Fig. 9A), indicating the presence of gas hydrates.
328
4.1.2 Site W17
329
Site W17 is located at the tip of the eastern submarine ridge in the southeastern corner of the drilling area,
330
adjacent to site W11 (Figs. 1B, 3, 5), which has a water depth of 1259 m. The actual drilling depth was ~315 mbsf,
331
and the geothermal gradient was 4.43 °C/100 m. The pilot hole LWD logging curves at site W17 exhibit an anomaly
332
at 210-270 mbsf. The resistivity increases significantly, and the acoustic travel-time difference decreases, suggesting
333
the presence of an approximately 60 m thick GHBZ (Fig. 8B). The actual coring results confirm that the depth of the
334
gas hydrates is well correlated with the logging anomaly layer. The core data from this site reveals that the gas
335
hydrates mainly occur over a 56 m interval from 206 mbsf to 265 mbsf. In addition, indications of gas hydrates are
336
also observed in several sections above 190 mbsf (Fig. 9B). Gas hydrates are dispersed in the pores of the sediments
337
and are not visible to the naked eye. During the drilling process, a significant number of massive hydrates was
17
338
observed, using a camera placed on the seabed frame, near the wellhead (Fig. 11D). In addition, the core infrared
339
scanning results exhibit significant negative thermal anomalies, which are presumably caused by hydrates (Fig. 9B).
340
The core obtained from 238 mbsf to 241 mbsf contains sediments with porridge-like characteristics, suggesting that
341
the hydrates have decomposed (Fig. 11E).
342
4.1.3 Site W18
343
Site W18 is located on the lower part of the western submarine ridge (Figs. 1B, 3, 6). The water depth was ~1285
344
m, and the actual drilling depth was ~234 mbsf. The geothermal gradient was 6.26 °C/100 m. The pilot hole logging
345
curves for this site contains an anomaly between 144 and 174 mbsf. The resistivity increases and the acoustic
346
travel-time difference decreases significantly, indicating that there are hydrates within this layer (Fig. 8C). The actual
347
coring indicates that the depth of the gas hydrates corresponds well with the anomalous layer in the logging (Fig.
348
10A). The core data from this site reveal that the gas hydrates occur over a 25 m interval from 147 mbsf to 172 mbsf.
349
In addition, gas hydrates with low saturations may occur at 137–147 mbsf because gas inflation cracks were observed
350
within the cores at these depths (Fig. 10A). The gas hydrates are disseminated within the pores of the sediments and
351
are not visible to the naked eye. Hydrate cores were obtained at site W18 at depths of 152 mbsf to 155 mbsf. By the
352
time the cores reached the deck, the hydrates had decomposed. The cores had a honeycomb appearance, and some of
353
the sediments exhibited porridge-like characteristics (Fig. 11F). The core sediments obtained at the depths of
354
155-158 mbsf exhibit distinct negative thermal anomalies on the infrared scanning image (Fig. 11G), indicating the
355
presence of hydrates within this layer. In addition, the cavities created by the decomposition of the hydrates were also
356
observed from 165.5 mbsf to 168.5 mbsf (Fig. 11H).
18
357
4.1.4 Site W19
358
Site W19 is also located on the lower part of the western submarine ridge, close to site W18 (Figs. 1B, 3, 7), with
359
a water depth of ~1274 m. The actual drilling depth was ~240 mbsf, and the geothermal gradient was 5.56 °C/100 m.
360
The pilot hole logging curves for this site reveal that the resistivity curves vary from 134 mbsf to 202 mbsf, and the
361
total thickness of the abnormal layer is approximately 68 m (Zhang et al., 2017) (Fig. 8D). The acoustic travel-time
362
differences within this layer decrease significantly and are the mirror image of the resistivity curve, indicating the
363
presence of gas hydrates. The actual coring demonstrated that the depth of the gas hydrates corresponds well with the
364
anomalous logging layer (Fig. 10B). The core data from this site revealed that gas hydrates are present over a 28 m
365
interval from 135 mbsf to 163.5 mbsf. The gas hydrates are disseminated within the pores of the sediments and are
366
not visible to the naked eye. Similar to site W17, a significant number of massive hydrates were observed near the
367
wellhead during the drilling process (Yang et al., 2015; Zhang et al., 2017). The cores obtained from depths of
368
134–137 mbsf and 140–142 mbsf show distinct indications of gas hydrates, such as cavities and a strong inflating
369
phenomenon from the dissociation of gas hydrates (Fig. 11I). Some of the hydrates in the sediments had decomposed
370
and turned mushy (Fig. 11J). In addition, the infrared images of the core sediments also show significant negative
371
anomalies (Fig. 10B), which fully demonstrate that these layers contain gas hydrates (Zhang et al., 2017).
372
373
4.2 Seismic reflection characteristics of drilling sites
374
Recognizing and identifying the submarine BSR is an effective method of exploring for gas-hydrates (Zillmer et
375
al., 2005; Majumdar et al., 2016).The distribution of hydrates and associated free gas below the GHSZ can be
376
roughly characterized by studying the seismic reflection features of the BSR and nearby strata (Hyndman and Davis, 19
377
1992; Haacke, et al., 2007; Crutchley et al., 2015).
378
The BSR in the GHPTR in the Shenhu area is widespread with prominent characteristics (Figs. 3–7), exhibiting
379
strong to relatively strong amplitude reflections generally crosscutting the nearby strata and roughly parallel to the
380
seafloor but with opposite polarities. Most of the identified BSR is distributed along the slope area and exhibits
381
medium to high continuous characteristics; however, the BSR is discontinuous in some locations. Based on the
382
seismic interpretation from the drilling sites within the GHPTR, the BSR is mainly located between ~170 mbsf and
383
~400 mbsf, and the length of a single BSR is ~6 km. The acoustic blanking reflections occur above the BSR in some
384
sites, such as sites W11 and W17 (Figs. 3–5). However, in some areas, the reflections directly above the BSR also
385
show a high amplitude obliquely adjacent to or connected to the BSR (Figs. 3–5). In addition, acoustic blanking,
386
masking, and chaotic reflections with significant vertical extensions are observed below the BSR (Figs. 3–7). The
387
drilling results confirm that the coring sites of the GMGS3 and 4 expedition-obtained hydrates correspond well to the
388
position of the BSR with a strong amplitude and good continuity. There are often also amplitude abnormalities above
389
and below the BSR (Guo et al., 2017; Zhang et al., 2017; Zhang et al., 2018b; Qian et al., 2018).
390
Based on the interpretation of the seismic data, the two-way seismic travel time of the BSR near site W11 is
391
1965 ms, and the depth of the BSR is approximately 200 mbsf (Guo et al., 2017). The BSR distinctly crosscuts the
392
ambient bedding with good continuity and strong amplitude. In addition, a pronounced amplitude-blanking zone
393
occurs above the strong reflections obliquely connecting to the BSR, indicating the accumulation of gas hydrates or
394
free gas (Fig. 4). Several high-angle faults occur below site W11. Enhanced reflections (ERs) were observed near
395
these faults. The two-way seismic travel time of the BSR near site W17 is 1968 ms, and the depth of the BSR is
396
approximately 230 mbsf. The BSR is characterized by good continuity and strong amplitude. It extended for 20
397
approximately 2.5 km and obliquely crosscut the surrounding strata. Similar to site W11, the amplitude-blanking
398
zone above the BSR is also prominent at site W17, and the seismic events below the BSR exhibit pull-down features
399
and have an abnormal velocity-amplitude structure, indicating the accumulation of gas hydrates above the BSR and
400
free gas below the BSR (Fig. 5). Several near-vertical faults are interpreted to exist in the lower left part of site W17,
401
and ERs are also present in the vicinity of these faults. Based on the interpretation of the seismic data across site W18,
402
a distinct BSR with good continuity and strong amplitude was identified on the seismic profile. The two-way seismic
403
travel time of the identified BSR is 1898 ms, and the depth of the BSR is approximately 171 mbsf. The BSR crosscuts
404
the surrounding bedding. No amplitude-blanking zones are present above the BSR, although acoustic masking is
405
prominent below the BSR (Fig. 6). The BSR is clearly divided into two sections with strong amplitude features near
406
site W19, as in the seismic profile (Fig. 7). The two-way seismic travel time of the BSR is 1888 ms, and the depth of
407
the BSR is approximately 170 mbsf. In addition, the BSR distinctly and obliquely crosscuts the sedimentary strata.
408
Two gliding faults nearly connect with the BSR and extend to the seafloor at W19 site. No distinct seismic-blanking
409
zones occur above the BSR at site W19, and the seismic reflections below the BSR are fuzzy and chaotic (Fig. 7).
410
411
4.3 Characteristics of hydrate logging curves
412
Coring sites W11, W17, W18, and W19 in the GHPTR showed distinct indications of gas hydrates during the
413
LWD process, and the GHBZ corresponded well with the well logging curve anomalies, which have a high apparent
414
resistivity, high acoustic velocity, low acoustic travel-time difference, relatively low density, and low natural gamma
415
ray value (Fig. 8) (Yang et al., 2017b; Yang et al., 2017c; Yang et al., 2017d; Zhang et al., 2017; Qian et al., 2018).
416
The resistivity logging curve for site W11 reveals a general high-value anomaly at 112–201.6 mbsf, with a 21
417
thickness of approximately 90 m. There are four high-value abnormal layers (Fig. 8A) located at 112–130 mbsf,
418
132–138 mbsf, 141–153 mbsf, and 158–201 mbsf. The maximum abnormal value of resistivity is approximately 5.6
419
Ω.m. The natural gamma curve value is between 43.75 and 98.75 API; mean natural gamma between the seafloor and
420
112 mbsf is 61.25 API; and natural gamma below 112 mbsf is approximately 72.5 API, with little change. The
421
acoustic travel-time difference curve mirrors the resistivity curve for the abnormal layers. The acoustic travel-time
422
difference value decreases significantly when the resistivity value increases. The minimum value of the acoustic
423
travel-time difference is approximately 132.5 us/ft (approximately 2300 m/s) at a depth of 170 mbsf. The density
424
curve shows a high anomaly of 2.13 g/cm3 at 115.38 mbsf, and the corresponding neutron curve decreases, which is
425
most likely due to changes in lithology. The density at 127.4 mbsf is significantly lower, with a value of
426
approximately 1.37 g/cm3; whereas, the corresponding neutron porosity increases significantly, exhibiting anomalous
427
characteristics typical of the GHBZ. In summary, the hydrates are inferred to exist at depths of 112–130 mbsf,
428
132–138 mbsf, 141–153 mbsf, and 158–201 mbsf. Samples of gas hydrates were recovered from the four
429
corresponding layers during the coring (Figs. 9A, 11A–C).
430
The logging curves for site W19 (Fig. 8D), which are described by Zhang et al. (2017) and Yang et al. (2015,
431
2017c, 2017d), reveal that the resistivity curve increases sharply from 1 Ω.m to 8.67 Ω.m above 134 mbsf, then
432
decreases slowly, and finally significantly decreases at 156 mbsf. The resistivity curve starts to fluctuate between 156
433
mbsf and 202 mbsf. The corresponding acoustic travel-time difference curve also decreases significantly. In addition,
434
the shape of the acoustic travel-time difference curve is the mirror image of the resistivity curve. Thus, we speculate
435
that the layer between 134 and 202 mbsf is the GHBZ. In addition, the natural gamma curve for this layer exhibits an
436
increasing trend, and the minimum acoustic travel-time difference of this layer is 119.2 us/ft (2557 m/s). In addition,
22
437
the density curve does not exhibit a decreasing trend; however, the neutron porosity exhibits a decreasing trend.
438
The characteristics of the logging curves for the GHBZ at sites W17 (Fig. 8B) and W18 (Fig. 8C) are similar to
439
those of the curve for site W19, i.e., high resistivity values and low acoustic travel-time differences. Generally, the
440
density and compensated neutron curves have no distinct response characteristics within the possible GHBZ at any
441
site. However, the logging values in the GHBZ at each site are different. The resistivity values of sites W18 and W19
442
are significantly higher than those at sites W11 and W17. The resistivity values of sites W18 and W19 decrease
443
with depth within the abnormal logging zone, exhibiting an anti-rhythm feature. However, resistivity logs of sites
444
W11 and W17 exhibit fluctuation characters. This indicates that the hydrate saturation gradually decreases with depth
445
within the GHBZ at sites W18 and W19; whereas, the saturation of the gas hydrates may fluctuate within the
446
abnormal logging sections at sites W11 and W17.
447
448
4.4 Features of gas-hydrate host sediments
449
The lithology and grain size analysis of the core sediments in the GHPTR show that the gas-hydrate host
450
sediments in this area are mainly fine grained. Four major types of lithology (Zhang et al., 2017; Kang et al., 2018;
451
Li et al., 2018; Li et al., 2019a), viz., calcareous clayey silt, calcareous silt, calcareous and siliceous clayey silt, and
452
siliceous and calcareous clayey silt, were identified in the coring sites (Fig. 12).
453
The sediments recovered from coring sites W11 and W17 have low clay content and relatively high sand content
454
in the upper part of the core; however, the lower part of the core has the opposite composition. The total core clay
455
content, silt content, sand content, and median grain size (Mz) of site W11 range from 14.2% to 38.7%, 61.1% to
23
456
83.0%, 0.07% to 8.51%, and 6.12 to 7.91 Ф, respectively (Fig. 12A). The total core clay content, silt content, sand
457
content, and median grain size of site W17 range from 16.1% to 37.7%, 46.1% to 82.0%, 0.09% to 18.70%, and 6.17
458
to 7.88 Ф, respectively (Fig. 12B). At a depth of 50.1 m in the core, the sediment consists of 37.4% clay, 56.1% silt,
459
and 16.5% sand, which may be due to sliding of the upper continental slope or depositional filling of channels.
460
In contrast to the drilling sites W11 and W17, the results of the grain size analysis show that the clay content of
461
site W19 gradually decreases with depth, ranging from 17.2% to 44.2%; the silt content ranges from 55.6% to 80.1%;
462
and the sand content ranges from 0.04% to 10.9%. The median grain size ranges from 6.14 to 7.97 Ф (Fig. 12D).
463
The grain size of the sediments recovered from site W18 is similar to that of site W19. The total core clay, silt,
464
and sand contents range from 17.5% to 33.9%, 54.2% to 80.0%, and 1.11%‐to 23.8%, respectively. The grain size
465
ranges from 5.82 to 7.58 Ф (Fig. 12C). In addition, commonly distributed foraminifera fossils were found at the
466
coring sites in the GHPTR, particularly sites W18 and W19 where abundant foraminifera fossils were found at
467
~100-170 mbsf (Figs. 11K, 13). Foraminifera fossils are the main source of the carbonate composition of the
468
sediments and are positively correlated with the concentration of sand, indicating that the foraminifera fossil shells
469
are a major component of the sand-scale sediments. In addition, it is worth noting that the total abundance of the
470
foraminifera in the GHSZ has a good correspondence with the concentration of CaCO3 and the variation in the
471
reservoir porosities.
472
Based on the results of the well-logging interpretation (Table 1), the hydrate reservoirs are generally
473
characterized by a relatively low permeability and high porosity. The average effective porosities of the hydrate
474
layers at site W11, W17, W18, and W19 were 34.5%, 32.2%, 56.7%, and 48.3%, respectively. The corresponding
475
average permeabilities were 0.22 mD, 0.32 mD, 100 mD, and 5.5 mD.
24
476
477
4.5 Velocity structures and acoustic impedance inversion of drilling sites
478
The high-precision velocity profile across sites W11 and W17 (Fig. 14A) shows that the layer above the BSR is
479
characterized by a high velocity of 1800-2000 m/s. This high-velocity anomaly coincides with the strong reflection
480
amplitude observed above the BSR, and the acoustic travel-time difference and resistivity curve are characterized by
481
decreasing and increasing trends, respectively, indicating that high velocity is associated with the presence of gas
482
hydrates. Above the high-velocity anomaly zones, the velocity is 1600-1700 m/s, i.e., normal strata velocity
483
characteristics, and the acoustic travel-time difference and resistivity curves are not significantly changed, indicating
484
the absence of gas hydrates in sediments. In the layer below the BSR, a low velocity anomaly with 1400-1600 m/s is
485
observed, which is significantly lower than the velocity of the surrounding strata, strongly indicating the
486
accumulation of free gas in the strata.
487
High-velocity anomalies with 1700-1900 m/s also occur in the strata above the BSR at site W19. However, the
488
strata velocity anomaly above the BSR at site W18 is not distinct, and the velocity is 1600-1700 m/s, which is only
489
slightly higher than the velocity of the surrounding strata (Fig. 14B). Corresponding to the abnormal velocity region,
490
the acoustic wave time difference and resistivity exhibit decreasing and increasing trends, respectively. This
491
anomalous velocity region coincides with the high-amplitude reflection above the BSR, indicating the presence of
492
gas hydrates in the sediments. The strata over the high-velocity anomaly area generally exhibit relatively
493
low-velocity characteristics; therefore, there may be free gas accumulation. In addition, a local, relatively
494
high-velocity anomaly (~1700 m/s) occurs near the seafloor between sites W19 and W18. In the strata below the BSR,
495
the low-velocity anomaly zones are distinct, and the velocity of the strata is 1400-1500 m/s, which also strongly 25
496
indicate the entrapment of free gas. In addition, the low-velocity anomaly region exhibits a large scrotiform structural
497
feature on the velocity profile, extending from 1900 ms down to at least 2500 ms.
498
Based on the seismic profile and p-wave impedance inversion profile analysis (Fig. 15), the inversion profile
499
resolution was improved compared with that of the seismic profile. The seismic inversion wave impedance is
500
generally consistent with the variation trend in the borehole p-wave impedance curve, and the lateral variation in the
501
wave impedance is consistent with the seismic reflection characteristics. The red region above ~2000 ms in Figure 15
502
represents the relatively higher p-wave impedance (
503
variation in the blue region with a relatively lower impedance ( ~3000) generally reflects the lateral heterogeneity
504
of the free-gas reservoir. In addition, the GHBZ exhibits a layered distribution on the inversion profile, and the FGBZ
505
and the GHBZ exhibit a distinct wave impedance difference. Except for site W11, the FGBZ was identified below the
506
GHBZ at sites W17, W18, and W19, which is consistent with the distribution of the free gas and gas hydrates
507
reflected by the above-mentioned velocity inversion profiles (Fig. 15).
3800), corresponding to the GHBZ; whereas the lateral
508
509
4.6 Modeling results of gas-hydrate stability zone
510
The calculated BGHSZ of SI (100% CH4) gas hydrates at site W11 is ~194 mbsf (~1504 mbsl), which is close
511
to the BSR (~200 mbsf) and base of the LWD electrical resistivity anomaly (~202 mbsf). The calculated BGHSZ of
512
the SII gas hydrates (99% C1 + 0.5% C2 + 0.5% C3) is 220 mbsf (~1530 mbsl). Considering the calculation error,
513
the base of the SI gas hydrates should be located at around 200 mbsf at site W11 (Fig. 16A). The calculated
514
BGHSZ of the SI (100% CH4) gas hydrates at site W17 is ~239 mbsf (~1498 mbsl), which is close to the BSR
515
(~230 mbsf) but significantly shallower than the base of the LWD electrical resistivity anomaly (~270 mbsf). In 26
516
addition, the BGHSZ of the SII gas hydrates calculated using 99% CH4 + 0.5% C2H6 +0.5% C3H8 is ~270 mbsf
517
(1529 mbsl), which is consistent with the base of the LWD electrical resistivity anomaly (Fig. 16B). The calculated
518
BGHSZ of the SI (100% CH4) gas hydrates at site W18 is ~161 mbsf (~1446 mbsl), which is close to the BSR
519
(~170 mbsf) but shallower than the base of the LWD electrical resistivity anomaly (~174 mbsf). In addition, the
520
BGHSZ of the SII gas hydrates calculated using 99% CH4 + 0.5% C2H6 + 0.5% C3H8 is ~189 mbsf (~1474 mbsl),
521
which is deeper than the base of the LWD electrical resistivity anomaly (Fig. 16C). The calculated BGHSZ of the
522
SI (100% CH4) gas hydrates at site W19 is ~165 mbsf (~1439 mbsl), which is close to the BSR (~170 mbsf) but
523
significantly shallower than the base of the LWD electrical resistivity anomaly (~185 mbsf). In addition, the
524
BGHSZ of the SII gas hydrates calculated using 99% CH4 + 0.5% C2H6 +0.5% C3H8 is ~192 mbsf (~1466 mbsl),
525
which is very close to the base of the LWD electrical resistivity anomaly (Fig. 16D). In addition, at each site, the
526
BGHSZ calculated using 95% CH4 + 2.5% C2H6 + 2.5% C3H8 is generally deeper than the BSR and BGHSZ
527
calculated using 99% CH4 + 0.5% C2H6 + 0.5% C3H8 (Fig. 16, Table 1).
528
529
5. Discussion
530
As mentioned already, gas hydrates with a high saturation of up to 76% were recovered in the fine-grained host
531
sediments of the GHPTR in the Shenhu area, which revealed the widespread distribution of distinct BSR and
532
amplitude anomalies including ERs, acoustic blanking, masking, and chaotic. All the gas hydrates encountered were
533
concluded to be of a fine, disseminated nature and were hosted in the clayey silt dominated sediments. The
534
gas-hydrate accumulations sampled were relatively thick and uniform compared with those of other sites worldwide.
535
For example, site W11 contains a remarkable zone of continuous gas hydrates over 90 m thick. In addition, the FGBZ 27
536
was identified below the GHSZ, indicating that the Shenhu area contains a gas-hydrate petroleum system with an
537
abundant hydrocarbon supply. Free gas was also present at some of the sites, and gas-hydrate formation was observed
538
on and around the seabed frame during drilling near the base of the resistivity anomalies (Yang et al., 2015). In
539
addition, the increased pore-water salinity above the top of the GHBZ observed at sites W18 and W19 (Figs. 16C, D)
540
indicates that these adjacent locations are part of a currently active system. Gas hydrates may be forming in these
541
sediments, with the resulting exclusion of saline fluids. In addition, both biogenic and thermogenic gases were
542
discovered in the hydrate gases. The depth of the calculated BGHSZ differs from the depth of the BSR and logging
543
anomalous sections, indicating the presence of gas hydrates below the BSR and even the coexistence of SI and SII gas
544
hydrates in the GHPTR. In summary, the GHPTR in the Shenhu area exhibits some fascinating and apparently unique
545
characteristics, which are of significance to investigating the accumulation mechanism of gas hydrates in the SCS.
546 547
5.1 Indications for gas-hydrate accumulation and hydrocarbon migration
548
As discussed above, seismic reflection anomalies, including high-amplitude reflections, acoustic blanking,
549
masking, and chaotic reflections occur above and below the BSR within the GHPTR. However, using the seismic
550
reflection to determine the geological implications of these reflection anomalies and identifying and distinguishing
551
hydrate layers and free gas are indeed challenging. However, relying solely on identifying the BSR to identify gas
552
hydrates may not be accurate. A recent development in gas-hydrate exploration is to use the event amplitude as well
553
as polarity (Boswell et al., 2016). Therefore, we identified and distinguished the hydrate distribution by making
554
synthetic seismograms to determine the top and bottom of the GHBZ (Figs. 17, 18). Based on the multi-well
555
calibration results, the GHBZ has a high resistivity, low acoustic travel-time difference, high impedance on the log
28
556
curves, and strong reflection characteristics on the seismic profiles. In addition, the strong amplitude reflection
557
characteristics of the two marking layers at the mud line of the seabed and at the top of the GHBZ are distinct (Figs.
558
17, 18); however, the reflection characteristics of the bottom interface of the GHBZ are different at each site. Some of
559
the sites exhibit a wave trough with strong amplitude characteristics, such as site W11 (Fig. 17). Other sites exhibit a
560
wave trough with low-amplitude characteristics or zero phase, such as site W18 (Fig. 18). These different reflection
561
characteristics are related to the thickness of the gas hydrates and physical properties of the host sediments.
562
The GHBZ exhibits two kinds of characteristics on the seismic profile. The first is a well with a thick single
563
layer (~10 m), which is characterized by obvious strong reflection characteristics. The top boundary of the
564
gas-hydrate layer is a strong reflection wave crest, and the bottom boundary is a strong reflection wave trough. In
565
addition, the inside of the GHBZ is characterized by strong amplitude, which is in sharp contrast to the relatively
566
weak amplitude outside the GHBZ. Site W11 on the eastern ridge is the most typical. The second is a well with a
567
single thin gas-hydrate layer. The GHBZ has no obvious reflection characteristics on the seismic section, and the
568
main performance is a weak wave crest reflection, which is typical of site W18 on the western ridge. The bottom
569
surface of the GHBZ, i.e., the BSR, is a strong wave trough reflection with distinct strata cross-cutting features,
570
which is clear throughout the GHPTR, and is consistent with the bottom surface of the GHBZ calibrated using the
571
drilling wells. Therefore, combined with the drilling data analysis, the gas-hydrate distribution within the GHPTR
572
can be qualitatively determined through the analysis of the polarity and reflection intensity of seismic reflections.
573
Significant acoustic blanking reflections often occur within the GHSZ. These are generally interpreted as the
574
presence of gas hydrates, accumulation of free gas, activity of fluid, and so on (Wu et al., 2005; Fraser et al., 2016;
575
Fraser, 2017; Wang and Pan, 2017; Behboudi et al., 2018). Distinct acoustic blanking zones were also identified
29
576
overlying the strong seismic reflections of the GHBZ at sites W11 and W17. The corresponding logging results show
577
that the resistivity of the blanking zone is very flat, there is no increase or decrease with depth, and the acoustic
578
travel-time difference log only decreases slightly (Fig. 14A). In addition, the seismic velocity profile shows that the
579
acoustic velocity of the blanking zone is approximately 1600-1800 m/s. This is not significantly different from the
580
normal sediment velocity; however, it is significantly different from the velocity of the strata containing an
581
accumulation of high saturation gas hydrates (Fig. 14A). Therefore, it is concluded that the acoustic blanking zones
582
overlying the strong reflections of the GHBZ at sites W11 and W17 do not indicate the accumulation of gas hydrates
583
or free gas; they rather indicate normal lithologically uniform fine-grained deposits.
584
Inclined strong, continuous events just below and connecting to the BSR were identified at sites W11, W17,
585
W18, and W19. These high amplitude reflections are interpreted to indicate the presence of free gas (Wang et al.,
586
2014; Li et al., 2018) (Figs. 3–7). Weak amplitude widespread acoustic blanking or chaotic reflections were found
587
below these strong reflections, indicating active gas-bearing fluid activity below the BSR. Generally, the impedance
588
contrast of free gas differs significantly from that of the overlying hydrate layers and the surrounding sedimentary
589
strata (Fig. 15). The accumulation of free gas is also controlled by the distribution characteristics of the strata;
590
therefore, free gas accumulation usually presents inclined multi-layered reflections with high-amplitude
591
characteristics. From the seismic reflection characteristics of the free gas in the GHPTR, the free-gas reservoirs of
592
all of the coring sites show strong reflection characteristics under the BSR (Figs. 3–7). The strong reflections can
593
be divided into two categories. The first is the strong reflection characteristics represented by sites W11 and W17,
594
which have extremely high seismic amplitudes and prominent high-frequency layered reflections under the BSR. In
595
addition, the top and bottom interfaces of the probable free-gas reservoirs are also clear (Fig. 14A). The second is
596
the strong reflection features represented by sites W18 and W19, which show that the adjacent reflections under the 30
597
BSR have high seismic amplitudes, but the amplitude gradually decreases downward and even changes into chaotic
598
and blanking reflections, indicating low saturation free gas within the reservoirs (Fig. 14B).
599
Sites W11 and W17 are located in the same geological structural position in the GHPTR. The free-gas
600
reservoirs under the BSR both exhibit strong reflections (Fig. 14A). However, the strong reflection has a finite
601
extent. Gas reservoirs cause multiple strong reflection wave groups, which have the same tendency as the strata but
602
distinctly crosscut the BSR and are different from those around sites W18 and W19 (Figs. 6, 7). In addition, the
603
strong reflection of the free-gas reservoir at site W17 rapidly weakens and terminates downward, forming a
604
prominent obliquely cross-cutting reflection feature, which is interpreted to be the bottom of the free-gas reservoir
605
(Fig. 14A). Coring sites W18 and W19 are located in similar geological structures. The free-gas reservoirs are well
606
developed below the hydrate layers, and their seismic reflection characteristics are basically the same. The top of
607
the free-gas reservoir exhibits strong reflection wave groups, whereas the strong reflection gradually transforms
608
into a weak reflection downward, which is more chaotic and similar to the reflection characteristics of the
609
surrounding strata (Fig. 14B). The strong reflections of the free-gas reservoir at site W19 are more prominent than
610
those at site W18, which is presumably related to the relatively higher structural position of site W19 and more free
611
gas accumulation.
612
5.2 Coexistence of gas hydrates and associated free gas
613
5.2.1 Low seismic velocity and p-wave impedance of free gas
614
Free gas is generally characterized by low-velocity anomalies on seismic velocity profiles (Fohrmann and
615
Pecher, 2012; Cordero et al., 2016). The low-medium velocity zones coincide with the strong reflection amplitude
616
below the GHBZ and exhibit a wide extension at different depths in the GHPTR (Fig. 14). As can be seen from 31
617
Figure 14B, there are low-velocity anomalies (blue zone) under the BSR at sites W18 and W19 with scrotiform
618
features, which are large scale and transversely continuous. The low-velocity zones are mainly concentrated in the
619
high part of the structure, and the top of the anomalous velocity area coincides with the strong seismic reflections.
620
In addition, they generally extend to a significant depth and exhibit a string-of-beads shape in the longitudinal
621
direction. We suggest that the deep part is related to the low-velocity anomaly formed by ongoing gas migrating
622
and charging, which is closely related to hydrocarbons transported from the deep source rocks. The low-velocity
623
anomaly at site W18 is more prominent, indicating a more developed free-gas reservoir. In addition, the bottom of
624
the low-velocity anomalous areas at sites W18 and W19 is relatively clear, which most likely indicates the bottom
625
of the free-gas reservoir.
626
There is no distinct low-velocity anomaly below the BSR at site W11 (Fig. 14A). The strata velocity is similar
627
to that of the surrounding sediments; therefore, there is no free-gas reservoir just below the GHSZ. However, a
628
local low-velocity anomaly is present to the south of site W11; however, the extent and thickness of the anomaly
629
are smaller than those at sites W18 and W19, and the scale of the free-gas reservoir is inferred to be limited. A
630
low-velocity anomaly area is also present beneath the BSR at site W17 (Fig. 14A), exhibiting a nearly horizontal
631
scrotiform distribution. The degree and extent of the low-velocity anomaly is also weaker and smaller than those at
632
sites W18 and W19. In addition, the low-velocity anomaly is confined to the vicinity of site W17 and generally
633
coincides with the strong seismic reflection. The bottom of the low-velocity zone is clear, which basically
634
corresponds with the bottom of the free-gas layer on seismic reflection. In addition, there is no low-velocity
635
anomaly in the deep part of sites W11 and W17, indicating that the distributions and scales of the free-gas
636
reservoirs are limited. The contribution of the hydrocarbons that migrated from the deep Paleogene source rocks to
32
637
the free-gas reservoirs below the GHBZ may be very limited or may even have ceased, and the accumulation of
638
free gas is inferred to be the result of the dissociation of gas hydrates at sites W11 and W17. Further study is needed
639
to verify this speculation.
640
The p-wave impedance inversion profile (Fig. 15) also clearly shows the distribution of the gas hydrates and
641
the underlying FGBZ in both submarine ridges. Consistent with the velocity inversion results, the distribution of
642
free gas in the lower part of the western ridge hydrates is significantly larger than that in the eastern ridge. However,
643
the thickness of the GHBZ in the western ridge is significantly smaller than that in the eastern ridge. Therefore, it is
644
speculated that, in addition to the supply of sufficient hydrate gas, other controlling factors such as the thickness
645
and physical properties of the reservoirs may control the thickness and distribution of the hydrates in the GHPTR.
646
5.2.2 Down-hole logging indications of gas hydrates and free gas
647
Using the acoustic travel-time difference, density, and compensation neutron three porosity log intersection
648
method, the GHBZ and FGBZ in the GHPTR were identified (Fig. 19). From the analysis results, a consistent feature
649
in each well is that the density and compensated neutron logs have no obvious corresponding features in the GHBZ.
650
However, the GHBZ is present in each well even when the adjacent wells have different characteristics on the
651
acoustic travel-time difference log, reflecting the complexity of the hydrate distribution in the GHPTR.
652
Except for site W11, FGBZs were identified below the GHBZ at sites W17, W18, and W19 (Fig. 19). The
653
free-gas layers exhibit different logging response characteristics in the different wells. The thickness of the FGBZ in
654
well W17 is small, but the electrical response is significant, thereby exhibiting relatively higher resistivity values and
655
rapidly decreasing acoustic travel-time differences, density, and neutrons. The FGBZs of sites W18 and W19 are
656
relatively thicker, especially at site W18 (~50 m thick); however, the electrical response is relatively less significant. 33
657
Compared with the upper and lower surrounding rocks, the resistivity log value slightly increases; whereas the three
658
porosity log decreases slightly.
659
By combining the seismic and velocity superimposed profiles with the impedance inversion profiles of the
660
coring sites within the GHPTR (Figs. 14, 15), we conclude that gas hydrates and free gas coexist in the GHPTR (Qian
661
et al., 2018), and the free gas reservoirs in the eastern ridge are most developed at site W17 and its northern part, and
662
rapidly decrease to site W11 until they disappear. In addition, compared with the western ridge area where sites W18
663
and W19 are located, the extent of the low-velocity anomaly in the eastern ridge is limited and the thickness of the
664
free gas reservoirs is significantly smaller. Therefore, the hydrate gas supply in the western ridge is more abundant
665
than that in the eastern ridge, and the contribution of deep thermogenic gas to gas-hydrate formation in the western
666
ridge may be greater than that to the eastern ridge, which is reflected by the hydrate gas compositions and isotopic
667
data (Zhang et al., 2019).
668
669
5.3 Hydrocarbon migration difference between eastern and western ridges
670
The formation of gas hydrates requires sufficient natural gases. In addition to in situ biogenic gas, thermogenic
671
gas, which is transported from the deep source kitchens to the shallow GHSZ along different migration pathways, is
672
also important. The types, distribution, and development characteristics of the hydrocarbon migration pathways
673
play a vital role in the accumulation of hydrates (Gorman et al., 2002; Wang et al., 2014; Satyavani et al., 2015).
674
Previous studies of the GMGS1 expedition demonstrated that the gas migration pathways are primarily gas
675
chimneys, which play an important role in the migration of hydrocarbons and accumulation of gas hydrate in the
676
drilling area (Su et al., 2014a; Qiao et al., 2014; Su et al., 2017; Zhang et al., 2018a). Based on seismic 34
677
interpretation, multiple hydrocarbon migration pathways, including mud diapirs, gas chimneys, high-angle faults,
678
and gliding faults, were identified within the GHPTR (Zhang et al., 2017; Zhang et al., 2018b). However, the types
679
and geological characteristics of the hydrocarbon migration pathways vary within the GHPTR, resulting in different
680
hydrocarbon migration efficiencies for the eastern and western ridges.
681
Similar to the GMGS1 drilling area, mud diapirs and gas chimneys acting as favorable pathways for gas
682
migration from depth to the shallow GHSZ were identified below the drilling and coring sites in the GHPTR (Su et
683
al., 2016; Zhang et al., 2018a; Zhang et al., 2018b). On the eastern ridge, acoustic blanking and masking zones
684
occur below the BSR at sites W11 and W17 (Fig. 20A), and several seismic events on both sides seem to terminate
685
at the edge of that amplitude-anomaly zone. The interior seismic reflection is chaotic. In the lower part, the seismic
686
events show pull-up features, which are likely the result of the upward migration of mud during mud diapirism. In
687
the upper part, pull-down features are seen on the seismic profile, which is likely caused by the trapping of free gas
688
that migrated upwards from the deep source rocks through the pathways provided by the gas chimneys and mud
689
diapirs (Løseth et al., 2009; Hustoft et al., 2010; Nakajima et al., 2014; Cartwright and Santamarina, 2015). ERs
690
commonly occur on both sides and in the interior of the chaotic reflection zone, indicating the trapping of free gas
691
in the sediments (Judd and Hovland, 1992; Heggland et al., 1997; Andreassen et al., 2007). In addition, by mapping
692
the instantaneous frequency image, the chaotic reflection zones show distinct low-frequency characteristics
693
compared with those of the surrounding sediments and strata (Fig. 20B), further demonstrating the result of gas
694
migrating and filling in the upper low-pressure strata through the mud diapir and gas chimney (Zhang et al., 2018b).
695
Mud diapirs were also identified in the deep strata (Fig. 20C) at sites W18 and W19 on the western ridge. They
696
result in anticline structures and are speculated to be the result of the upward movement of mud. Furthermore,
35
697
large-scale low instantaneous frequency features appear on the instantaneous frequency profile (Fig. 20D),
698
indicating the intense migration and charging processes of hydrocarbons below sites W18 and W19. By comparing
699
the mud diapirs developed below the two ridges, we conclude that the scale of the mud diapir under the western
700
ridge is significantly larger than that under the eastern ridge (Fig. 20). In addition, by comparing the extent of the
701
chaotic reflections and the low instantaneous frequency between the coring sites, we conclude that the hydrocarbon
702
migration and charging activities at sites W18 and W19 on the western ridge are stronger than those at sites W11
703
and W17 on the eastern ridge. These observations correspond well with the distribution and enrichment features of
704
the free gas within the two ridges, which is reflected by the relatively low velocity and the low instantaneous
705
frequency zones (Figs. 14, 20).
706
As stated above, high-angle faults were identified below sites W11 and W17 in the GHPTR. Some of the
707
nearly vertical faults penetrate the deep Paleogene source rocks and extend upward to the BSR. Bright spots with
708
an enhanced amplitude are generally observed near these faults (Figs. 3–5), indicating that deep-seated gas has
709
migrated along the faults and was captured by the adjacent reservoirs (Su et al., 2016; Zhang et al., 2018b).
710
Therefore, these high-angle faults act as important migration pathways and supply the hydrate accumulation with
711
sufficient gases, particularly the thermogenic gas at sites W11 and W17. In contrast, no large-scale high-angle faults
712
connect the deep source rocks below sites W18 and W19. However, small faults and fractures, which are hard to
713
identify due to the chaotic and acoustic masking seismic features, may be present below these drilling sites (Figs. 3,
714
6, 7). There are gas hydrates sourced from the lateral migration of hydrocarbons at sites W18 and W19 (Su et al.,
715
2014a; Su et al., 2017; Zhang et al., 2018b). The most apparent are the gliding faults and sliding surfaces resulted
716
from submarine slumps, which constitute lateral migration pathways for shallow gases (Zhang et al., 2018b). The
36
717
distribution areas of the BSR generally coincide with the sliding surface at sites W18 and W19 (Figs. 6, 7), and
718
continuous reflections with strong amplitudes generally occur along these sliding surfaces, indicating that the gases
719
migrate laterally along the sliding surfaces toward the incline direction of the strata. From the seismic profile across
720
sites W18 and W19 (Figs. 3, 6, 7), the strong reflection features of the BSR show a clear cross-cutting relationship
721
with the strata. Several slump faults even crosscut the BSR and extend to the seafloor. We suggest that these faults
722
act as pathways for the migration of gas near the BSR and its further migration into the GHSZ, which would
723
increase the saturation and distribution range of gas hydrates (Su et al., 2014a; Su et al., 2017; Zhang et al., 2018b).
724
Unlike the western ridge, there was no lateral migration of hydrocarbons observed within the GHSZ at sites W11
725
and W17 on the eastern ridge. As a consequence, significantly more hydrocarbon can accumulate within the GHSZ
726
in the western ridge than in the eastern ridge. The distribution range of the gas hydrates in the western ridge is
727
larger than that in the eastern ridge. This is most likely the reason why the length of the BSR in the western ridge is
728
significantly longer than that in the eastern ridge (Figs. 3–7). Actually, the distribution area of the hydrate orebody
729
controlled by wells W18 and W19 (11.24 km2) is significantly larger than that controlled by wells W11 and W17
730
(6.42 km2) (Zhang et al., 2018c), which also suggests that the scope of the gas supply in the western ridge is larger
731
than that in the eastern ridge. Therefore, we conclude that there are differences in the natural gas migration and
732
accumulation between the eastern ridge and the western ridge due to the differential development of hydrocarbon
733
migration pathways. The efficiency of gas migration in the western ridge is higher than that in the eastern ridge,
734
resulting in differences in the gas migration flux and gas-hydrate accumulation.
735
37
736
5.4 Inconsistent distribution relationship among BSR, BGHSZ, and gas hydrates
737
In general, the BSR represents the distribution base of the SI gas hydrates, which is sourced by 100% methane.
738
However, as discussed above, there is a difference between the BSR depth identified from the seismic profile and the
739
BGHSZ calculated using the phase equilibrium curve for the GHPTR in the Shenhu area. The depths of the BSR and
740
the calculated BGHSZ are generally shallower than the base of the LWD electrical resistivity anomaly (Table 1, Fig.
741
16). It is proposed that this difference is closely related to the accumulation of thermogenic gas hydrates in the
742
GHPTR (Liang et al., 2017; Wei et al., 2018; Zhang et al., 2019). The evidence of the coexistence of SI and SII gas
743
hydrates has been reported in the Shenhu area by previous researchers. Liang et al. (2017) found gas hydrates below
744
the BSR and suggested that deep thermogenic fluid locally entrapped within the shallow-buried sediments may
745
reinforce the SII gas-hydrate accumulation. Based on the composition of hydrate gas, Zhang et al. (2017, 2019) also
746
suggested that both SI and SII gas hydrates are present in the Shenhu area due to a thermogenic gas supply for the
747
accumulation of the gas hydrates. Qian et al. (2018) provided log evidence for the coexistence of SII gas hydrates and
748
free gas below the BSR and calculated the distribution depth of the SII gas hydrates below the SI gas hydrates based
749
on the logging data at site W17 in the Shenhu area. Wei et al. (2018) discovered direct evidence for the occurrence of
750
SII gas hydrates using laser Raman spectroscopy and log data for the Shenhu area. In addition, the evidence of SII gas
751
hydrates below the BSR has recently been found in the eastern part of the Qiongdongnan Basin, which is adjacent to
752
the Shenhu area (Ye et al., 2019; Wei et al., 2019). SII gas hydrates located below the BSR have also been discovered
753
in other places around the world, such as the convergent margin offshore of NW Borneo (Paganoni et al., 2016).
754
The above-mentioned occurrence and distribution characteristics of gas hydrates indicate that they are not only
755
always distributed above the BSR but also present under the BSR based on seismic data. There are distinct logging 38
756
anomalies indicating the presence of gas hydrates below the BSR (Liang et al., 2017; Qian et al., 2018).
757
Furthermore, hydrate-derived cores and pore-water freshening have also been found below the BSR at sites W17,
758
W18, and W19 (Yang et al., 2017d; Guo et al., 2017) (Fig. 16), indicating that the BSR is not the BGHSZ and that
759
SI and SII gas hydrates likely coexist within the GHPTR in the Shenhu area.
760
The calculated BGHSZ of the SI (100% CH4) gas hydrates at sites W11 indicates that the base of the SI gas
761
hydrates should be around 200 mbsf, which is close to the BSR (~200 mbsf) and base of the LWD electrical
762
resistivity anomaly (~202 mbsf). There is no evidence of gas hydrates in the two cores below 200 mbsf, and there is
763
no pore-water freshening anomaly below the BSR (Fig. 16A). Therefore, no SII gas hydrates are present below the
764
BSR or base of SI GHSZ at site W11.
765
The calculated BGHSZs of the SI (100% CH4) gas hydrates at sites W17 and W18 are close to the BSR but are
766
significantly shallower than the base of the LWD electrical resistivity anomaly (Table 1, Figs. 16B, C). There is
767
clear evidence for gas hydrates in the core and the pore-water freshening and supporting evidence from the core
768
thermal anomalies below the BSR and the LWD electrical resistivity anomaly (Figs. 16B, C) (Yang et al., 2015).
769
Hence, there is strong evidence for the presence of SII gas hydrates below the BGHSZ of the SI gas hydrates at
770
sites W17 and W18.
771
The calculated BGHSZ of the SI (100% CH4) gas hydrates at site W19 is close to the BSR (~170 mbsf) but is
772
significantly shallower than the base of the LWD electrical resistivity anomaly (~185 mbsf) (Fig. 16D). The
773
calculated BGHSZ of the SII gas hydrates (99% CH4 + 0.5% C2H6 + 0.5% C3H8) is very close to the base of the
774
LWD electrical resistivity anomaly. It is speculated that SII gas hydrates are present below the BSR based on the
775
LWD anomaly, hydrate gas composition, and isotope information acquired from site W19 (Zhang et al., 2017, 39
776
Zhang et al., 2019). However, all the cores were shallower than 170 mbsf; therefore, no pore-water data is available
777
below this depth, and it is not known whether SII gas hydrates are actually present below the base of the SI gas
778
hydrates (Fig. 16D).
779
As discussed above, there is a dual supply of biogenic and thermogenic gases in the hydrate gas source in the
780
GHPTR in the Shenhu area. Owing to the supply of thermogenic gas, C2+ gas may enter the hydrate cages, which may
781
result in the coexistence of SI and SII gas hydrates. In addition, under the same temperature and pressure conditions,
782
the distribution base of the SII gas hydrates will expand downward, eventually causing the distribution of the SII gas
783
hydrates below the BSR (Zhang et al., 2019). The fact that the GHSZ calculated using 100% methane is inconsistent
784
with the depth of the BSR may be due to the presence of SII gas hydrates above the BSR, i.e., the SI gas hydrates
785
coexist with the SII gas hydrates in the GHPTR (Liang et al., 2017; Qian et al., 2018; Wei et al., 2018; Zhang et al.,
786
2019).
787
The discovery of SII gas hydrates in the GHPTR further confirms the contribution of deep thermogenic gas to
788
gas-hydrate accumulation, and it also confirms that the above described gas migration pathways can act as a bridge
789
between the natural gas from the Paleogene source rocks and the shallow GHSZ. In addition, the BSR is not
790
indicative of the BGHSZ but may instead be regarded as a transitional indicator of SI and SII gas hydrates in the
791
GHPTR. The distribution depth of the SII gas hydrates is deeper than the base of the SI gas hydrates, and the resource
792
amount of the gas hydrates is larger than the original estimation for the GHPTR. More deep drilling and coring below
793
the BSR are needed to characterize the gas-hydrate petroleum system and reevaluate the resource potential of the
794
Shenhu area.
795 40
796
5.5 Impact of reservoir characteristics on gas-hydrate accumulation
797
Based on the LWD data and gas-hydrate saturation calculation results (Figs. 8, 16, 19), there are variations in
798
the distribution and saturation of gas hydrates in the different layers of the same site. However, there are no
799
significant differences in the parameter characteristics of the lithologies of the gas-hydrate-bearing reservoirs
800
(Figure 12). The host sediments in the four cored holes are mainly calcareous clayey silt and calcareous silt, and the
801
hydrate reservoir is generally fine grained. The grain-size analysis results show that the grain sizes of the western
802
and eastern ridges differ, and the core sediments recovered from sites W18 and W19 have a relatively high clay
803
content; whereas, the core sediments obtained from sites W11 and W17 have a relatively high silt content (Fig. 12).
804
When comparing the sediment samples from the GHBZ with sediment samples from gas-hydrate-free zones, their
805
geometric parameters, viz., median grain size, sorting, skewness, and kurtosis, and main mineral compositions
806
(except for calcium carbonate) do not show significant variations in the GMGS4 coring sites (Li et al., 2019a).
807
However, gas hydrates with high saturation were recovered from all the coring sites during the GMGS 3 and 4
808
expeditions. Thus, the lithology may not be the factor controlling the differential plane accumulation of gas
809
hydrates in the different drilling and coring sites within the GHPTR (Zhang et al., 2017; Li et al., 2019a).
810
Nevertheless, the vertical distribution of the gas hydrates in the same site may be impacted and controlled by the
811
physical properties of the host sediments. Based on the physical property parameters of the reservoirs in the coring
812
sites with high-saturation hydrates, the hydrate reservoirs have a relatively high porosity of 33.2-56.7%. It is
813
necessary to explain why reservoirs mainly consisting of fine-grained sediments have such a relatively high
814
porosity. It is proposed that the sediments of the hydrate reservoirs are shallowly buried, and some pore spaces are
815
retained owing to the structure of the skeleton particles because they are less affected by sedimentary compaction
41
816
(Zhang et al., 2017). There are also a significant number of foraminifera fossils in the sediments acquired from sites
817
W18 and W19 (Figs. 11J, 13). Both the grain size of the fine-grained sediments and the roundness of the sediment
818
particles is higher, providing more space for the formation and accumulation of hydrates, and ultimately, a higher
819
saturation of the hydrates formed (Chen et al., 2009; Kraemer et al., 2000; Chen et al., 2013; Zhang et al., 2017; Li
820
et al., 2019a). We found that the low gamma ray response recorded by the LWD at sites W18 and W19 was actually
821
caused by the high calcareous content and the abundance of sand-sized forams. This observation is consistent with
822
the findings from GMGS1 in 2007, which also found rich gas hydrates in the foram-rich silt clays of nearby
823
locations (Chen et al., 2013; Wang et al., 2014). The ventricular structure of the foraminiferal fossil shells
824
constitutes a rich micropore space in the sediments, which increases the porosity of the hydrate reservoir and
825
provides favorable conditions for the formation of hydrates. However, it must be pointed out that there is
826
necessarily no correlation between the high abundance of foraminifera and gas hydrates with high saturation. While
827
there is a significantly high large calcareous component in the GHBZ at sites W18 and W19, a high abundance of
828
foraminifera and large calcareous component are also present above the GHBZ (Fig. 13). There is no such
829
indication of high calcareous contents at sites W11 and W17 where gas hydrates with saturation of up to 76% have
830
been recovered, indicating that the presence of calcareous material is not a prerequisite for pore-filling gas-hydrate
831
occurrence in fine-grained sediments at these locations in the GHPTR. The reservoir permeability shows a
832
significant variation, ranging from 0.22-100 mD, with depth at coring sites W11, W17, W18, and W19 in the
833
GHPTR (Table 1). Therefore, it is concluded that the variations in the physical properties of the host sediments,
834
rather than their lithologies, may lead to variations in gas-hydrate saturation between the different layers of the
835
different drilling wells or coring sites.
42
836
In terms of gas-hydrate production, the gas hydrates that have been successfully exploited around the world
837
have relatively high saturations (generally exceeding 60%) and predominately accumulate in coarse-grained
838
reservoirs with high porosities and permeabilities. The properties of the hydrate reservoirs in the Shenhu area are
839
significantly different from those discovered in the United States, Canada, and Japan. The lithologies of the hydrate
840
reservoirs in Canada and the United States are a glutenite type (Dallimore and Collett, 2005; Schoderbek and
841
Boswell, 2011). The hydrate reservoirs in Japan are generally of the coarse sand type (Fujii et al., 2015). The
842
lithology of the hydrate reservoir in the Shenhu area is fine grained and is dominated by clayey silt. Furthermore,
843
the reservoir permeability of the coring sites of the GMGS3 expedition is generally very low and varies
844
significantly. The coring sites of the GMGS4 expedition have permeabilities of 2-40 mD inside and outside the
845
GHBZ (Yang et al., 2017d); therefore, the permeabilities of these reservoirs are worse than those of other hydrate
846
reservoirs across the world (Li et al., 2018; Zhang et al., 2018c). However, owing to the presence of foraminifera,
847
the hydrate reservoir space is larger than expected from the lithology, and the effective matching of various types of
848
gas migration pathways and sufficient gas supply in the drilling area has led to the formation of a wide distribution
849
of high saturation gas hydrates in a fine-grained reservoirs. Furthermore, a successful production test of gas-hydrate
850
production was performed in the Shenhu area. It lasted for two months, with a mean daily yield of 5151 m3 in the
851
GHPTR (Li et al., 2018). This demonstrates that the gas hydrates accumulated in the fine-grained clayey silt can be
852
exploited, and the poor permeabilities of the hydrate reservoirs may not be a limiting factor affecting gas
853
production compared with the hydrate production test reservoirs with relatively high permeabilities but low gas
854
yields (Chen et al., 2018; Yamamoto et al., 2019).
855
43
856
5.6 Optimization of gas-hydrate drilling and production sites
857
In addition to the high porosities and permeabilities of hydrate reservoirs, which are crucial for hydrate
858
production, gas hydrates with high saturations and large thicknesses are preferred for hydrate exploitation because
859
they have larger quantities of gas resources within a given area. Thus, a method for discovering hydrates with large
860
thicknesses and high saturations is of significance worldwide (Dallimore et al., 2005; Anderson et al., 2011; Ito et
861
al., 2015). The above-discussed geological and geophysical characteristics of the drilling sites and the related
862
hydrate geochemistry in the study area demonstrate that the distribution of gas hydrates varies across sites and with
863
depth at the same site. Hence, identification of factors controlling the differential distribution of hydrates is the key
864
to the future exploration of gas hydrates with large thicknesses and high saturations in the Shenhu area, and even
865
throughout the SCS in the future. The concept of a gas-hydrate petroleum system (Collett et al., 2009) is an
866
effective way of characterizing and understanding gas-hydrate accumulation and has successfully aided the
867
exploration of gas hydrates around the world, such as in the Gulf of Mexico and offshore of India (Collett et al.,
868
2012; Collett et al., 2014). Although the gas-hydrate accumulations in the GHPTR are different from those in the
869
main hydrate occurrence areas, the concept of a gas-hydrate petroleum system can be applied to the exploration of
870
gas hydrates with high saturations and large thicknesses in the fine-grained sediments of the GHPTR (Wang et al.,
871
2014; Su et al., 2016; Wang et al., 2018). As discussed above, the gas supply, hydrocarbon migration pathways, and
872
reservoir properties are the three key factors that control the migration and accumulation of gas hydrates in the
873
Shenhu area.
874
Conventional oil and gas exploration has demonstrated that the Baiyun Sag is a huge hydrocarbon-generating
875
sag (Zhu et al., 2008; Zhu et al., 2009; Zhu et al., 2012). Whether of deep thermogenic gas or shallow biogenic gas, 44
876
the gas source is sufficient and can provide sufficient supply for hydrate formation in the study area (Fu et al., 2010;
877
He et al., 2013; Liang et al., 2014; Su et al., 2014b; Zhang et al., 2014; Zhang et al., 2019). However, as shown at
878
the GMGS3 and 4 coring sites, a sufficient hydrocarbon supply and coexistence of gas hydrates and associated free
879
gas may be preferred to the accumulation of high saturation gas hydrates. The gas-bearing fluid activities around
880
the coring sites may result in variable distribution of hydrates in the GHPTR. The presence of free gas below the
881
BSR indicates that the GHPTR in the Shenhu area is a complex hydrate accumulation system with disseminated gas
882
hydrates and free gas, which may be in a state of dynamic equilibrium due to the dual supply of sufficient biogenic
883
and thermogenic gases.
884
Drilling and coring results have shown that the GMGS3 and 4 coring sites with high-saturation hydrates are
885
mainly located in the down-dip positions along the canyon ridges (Fig. 1B). Compared with other sites with a
886
relatively low saturation, the sites with high saturation are located at the inclined end of the submarine canyons and
887
are significantly closer to the center of the Baiyun Sag (Yang et al., 2017a; Yang et al., 2017c; Yang et al., 2017d).
888
The geochemical data for the above coring sites indicate that the hydrate gas is mainly mixed gas, and thermogenic
889
gas also makes an important contribution (Zhang et al., 2019). However, the hydrate saturation of most of the sites
890
located in the upper and middle sections of the submarine ridge is relatively low (Yang et al., 2017b). Therefore, the
891
variations in the hydrate saturations and distributions of the different sites may be related to their structural
892
positions in the depressions. The differential development of hydrocarbon migration pathways may be one of the
893
important factors controlling the variations in hydrate saturation and vertical distributions at different sites in the
894
GHPTR (Zhang et al., 2018b), which is reflected by sites W11 and W17 on the eastern ridge and sites W18 and
895
W19 on the western ridge. Therefore, the areas or structures where the gas migration pathways develop and have a
45
896
good spatial coupling correspondence with the GHSZ are advantageous targets for exploring and obtaining higher
897
saturation hydrates (Zhang et al., 2018b). When follow-up drilling sites are selected, in addition to confirming the
898
sufficiency of the gas source, it is necessary to assess the development characteristics of the regional gas-bearing
899
fluid migration pathways and their coupling relationships with the other conditions for gas-hydrate accumulation.
900
Future studies should pay attention to not only the large-scale vertical migration pathways (including high-angel
901
faults, gas chimneys, and mud diapirs developed under the GHSZ) but also to the relatively smaller migration
902
pathways (including the gliding faults or cracks within the GHSZ). These migration pathways, although small in
903
scale, are numerous and widely distributed within the GHSZ. Furthermore, they may have a significant impact on
904
hydrate saturation and thickness over a long period of time.
905
Based on the lithologies and physical properties of the hydrate reservoirs, the physical properties of reservoirs
906
may affect the distribution of gas hydrates, resulting in differences in hydrate saturation at the different layers and
907
sites. Therefore, the characterization of the sediment properties is an effective way of identifying and locating
908
relatively high porosity and permeability reservoirs for further exploration of higher saturation and large-scale
909
hydrate resources, which are favorable for the exploitation of hydrates in the SCS. In general, fine-grained hydrate
910
reservoirs may not be favorable for hydrate development; however, the gas hydrates accumulated in the GHPTR
911
are characterized by a wide distribution, high saturation, large reservoir thickness, and high reservoir porosity,
912
which satisfy the basic conditions for hydrate production.
913
914
915
6. Conclusions
(1) Seismic indications of disseminated‐hydrates with high saturations and associated free gas in the gas-hydrate 46
916
production test region (GHPTR) include (a) widespread distinct BSRs, (b) enhanced seismic reflections (ERs) within
917
the gas-hydrate stability zone (GHSZ), (c) ERs connecting the BSR below the GHSZ, and (d) ERs, acoustic blanking,
918
and masking associated with high-angle faults, gas chimneys, and mud diapirs.
919
(2) Two types of GHBZs were identified. One is a well with a thick single layer (~10 m), which is characterized
920
by distinct strong reflections. The top boundary of the gas-hydrate layer is characterized by a strong peak leading
921
seismic reflector, and the bottom boundary is a strong reflection wave trough. The other type of the gas-hydrate
922
concurrence is the well with a thin single layer of gas hydrates, which shows no obvious reflection characteristics on
923
the seismic section and appears as a weak peak seismic reflection. The bottom surface of the GHBZ is characterized
924
by trough reflectors with distinct strata cross-cutting features.
925
(3) The free-gas-bearing zones (FGBZ) at sites W18 and W19, which generally extend to a significant depth,
926
are related to the low-velocity anomaly formed by ongoing gas migration and charging, which are closely related to
927
the hydrocarbons transported from the deep Paleogene source rocks. In contrast, the contribution of hydrocarbons
928
migrated from the deep source rocks to the FGBZ below the GHBZ at sites W11 and W17 may be limited or may
929
even have ceased. The accumulation of free gas is inferred to be the result of the dissociation of gas hydrates.
930
(4) There are variations in the types and geological characteristics of the hydrocarbon migration pathways of
931
sites W18 and W19 on the western ridge and sites W11 and W17 on the eastern ridge in the GHPTR. The efficiency
932
of gas migration in the western ridge may be higher than that in the eastern ridge, resulting in variations in the type of
933
hydrate gas, thickness of the GHBZ, and the gas migration flux and accumulation.
934
(5) The dual supply of thermogenic and biogenic gases results in the inconsistent distribution relationship
935
among the BSR, BGHSZ, and gas hydrates. The BSR is not indicative of the BGHSZ; instead it may be regarded as 47
936
a transitional indicator of SI and SII gas hydrates in the GHPTR. ‐
937
(6)‐Despite the fine-grained host sediments that dominate the GHPTR, relatively coarse-grained sedimentary
938
reservoirs should be the key to high-saturation hydrate accumulation. However, the presence of foraminifera is not
939
a prerequisite for the emergence of high-saturation hydrates. Coupling and matching of the geological conditions,
940
including a nearby hydrocarbon generation center, sufficient gas supply, multiple types of favorable gas migration
941
pathways, and relatively high reservoir porosity promote the formation of thick, highly saturated, gas-hydrate
942
reservoirs in the fine-grained sediments in the GHPTR.‐
943
944
Acknowledgements
945
This work was supported by the National Natural Science foundation of China (Nos. 41806071, 41602149,
946
41776056), Key Special Project for Introduced Talents Team of Southern Marine Science and Engineering
947
Guangdong
948
(2018YFC0310000), China Postdoctoral Science Foundation (No. 2017M622655), and Open Found of Key
949
Laboratory of Marine Mineral Resources, Ministry of Natural Resources (No. KLMMR-2017-A-13). The authors
950
wish to thank all those who contributed to the success of the China National Gas Hydrate Program Expedition 3
951
and 4. We would like to thank all reviewers and editors for their helpful suggestions and constructive comments
952
that helped us improve this manuscript.
Laboratory
(Guangzhou)
(GML2019ZD0102),
953
954 48
National
Key
R&D
Program
of
China
955 956
References
957
Anderson, B. J., Kurihara, M., White, M. D., Moridis, G. J., Wilson, S. J., Pooladi-Darvish, M., Gaddipati, M.,
958
Masuda, Y., Collett, T. S., Hunter, R. B., Narita, H., Rose, K., Boswell, R. 2011. Regional long-term production
959
modeling from a single well test, Mount Elbert gas hydrate stratigraphic test well, Alaska North slope. Marine
960
and petroleum geology, 28(2), 493-501.
961
Andreassen, K., Nilssen, E. G., Ødegaard, C. M. 2007. Analysis of shallow gas and fluid migration within the
962
Plio-Pleistocene sedimentary succession of the SW Barents Sea continental margin using 3D seismic data.
963
Geo-Marine Letters, 27(2-4), 155-171.
964
Behboudi, E., Keshavarz, N., & Naderi, A. 2018. Identification of Gas Accumulation Adjacent to the Gas Hydrate
965
Bearing Zone by Inversion Utilizing AVO Attribute. Journal of Petroleum Science and Technology, 8(3), 42-52.
966
Boswell, R., Collett, T. 2006. The gas hydrates resource pyramid. Natural Gas & Oil, 304, 285-4541.
967
Boswell, R., Collett, T. S., Frye, M., Shedd, W., McConnell, D. R., Shelander, D. 2012. Subsurface gas hydrates in the
968
969 970
971 972
973
northern Gulf of Mexico. Marine and Petroleum Geology, 34(1), 4-30.
Boswell, R., Shipp, C., Reichel, T., Shelander, D., Saeki, T., Frye, M., Shedd, W., Collett, T. S., McConnell, D. R. 2016. Prospecting for marine gas hydrate resources. Interpretation, 4(1), SA13-SA24.
Cartwright, J., Santamarina, C. 2015. Seismic characteristics of fluid escape pipes in sedimentary basins: implications for pipe genesis. Marine and Petroleum Geology, 65, 126-140.
Chen ,F., Su, X., Zhou, Y., Lu, H. F., Liu, G. H., Chen, Z. X., Chen, C. Y. 2009. Variations in biogenic components of 49
974
late Miocene-Holocene sediments from Shenhu area in the northern South China Sea and their geological
975
implication. Marine and Quaternary Geology, 29(2), 1-8.( in Chinese with English abstract)
976
Chen, F., Su, X., Lu, H. F., Zhou, Y., Zhuang, C. 2013. Relations between biogenic component (Foraminifera) and
977
highly saturated gas hydrates distribution from Shenhu Area,northern South China Sea. Earth Science, 38(5),
978
907-915. ( in Chinese with English abstract)
979
Chen, L., Feng, Y., Okajima, J., Komiya, A., & Maruyama, S. 2018. Production behavior and numerical analysis for
980
2017 methane hydrate extraction test of Shenhu, South China Sea. Journal of Natural Gas Science and
981
Engineering, 53, 55-66.
982
Choi, J.; Kim, J.-H.; Torres, M.E.; Hong,W.-L.; Lee, J.-W.; Yi, B.Y.; Bahk, J.J.; Lee, K.E. 2013. Gas origin and
983
migration in the Ulleung Basin, East Sea: Results from the Second Ulleung Basin Gas Hydrate Drilling
984
Expedition (UBGH2). Mar. Pet. Geol, 47, 113–124.
985 986
China Geological Survey, Ministry of Land and Resources.2016. One Hundred achievements of China's geological survey. Beijing: Geological Publishing House, 432-435.
987
Collett, T. S. 2002. Energy resource potential of natural gas hydrates. AAPG bulletin, 86(11), 1971-1992.
988
Collett, T. S. 2004. Gas hydrates as a future energy resource. Geotimes, 49, 24-27.
989
Collett, T.S., Johnson, A.H., Knapp, C.C., Boswell, R., 2009. Natural Gas Hydrates: a Review. American Association
990
of Petroleum Geologists Memoir, 89, 146-219.
991
Collett, T. S., Boswell, R., Cochran, J. R., Kumar, P., Lall, M., Mazumdar, A.,Ramana, M. V., Ramprasad, T., Riedel,
992
M., Sain, K., Sathe, V. A., Vishwanath, K., NGHP Expedition 01 Scientific Party. 2014. Geologic implications 50
993
of gas hydrates in the offshore of India: Results of the National Gas Hydrate Program Expedition 01. Marine and
994
Petroleum Geology, 58, 3-28.
995
Collett, T. S., Lee, M. W., Zyrianova, M. V., Mrozewski, S. A., Guerin, G., Cook, A. E., Goldberg, D. S. 2012. Gulf of
996
Mexico Gas Hydrate Joint Industry Project Leg II logging-while-drilling data acquisition and analysis. Marine
997
and Petroleum Geology, 34(1), 41-61.
998
Collett, T.S., Riedel, M., Cochran, J. Boswell, R., Presley, J., Kumar, P., Sathe, A. 2008. Indian National Gas
999
Hydrate Program Expedition 01 Initial Reports: Expedition 01 of the Indian National Gas Hydrate Program
1000
from Mumbai, India to Chennai, India; Sites NGHP-01-01 through NGHP-01-21, April 2006–August 2006,
1001
Initial Report, Directorate General of Hydrocarbons, Ministry of Petroleum and Natural Gas, Noida,
1002
India,2008.
1003
Cong, X. R., Su, M., Wu, N. Y., Qiao, S. H., Sha, Z. B., Lu ,H. L., Su, P. B.2018.Contribution of Thermogenic Gases
1004
to Hydrate Accumulation under the Marine Hydrocarbon-Rich Depression Setting. Acta Geologica Sinica,
1005
92(1), 170-183. ( in Chinese with English abstract)
1006 1007
1008 1009
Cordero, V., De la Cruz, I., Tinivella, U., Villar Muñoz, L. A., Giustiniani, M. 2016. Gas hydrate and free gas estimation from seismic analysis offshore Chiloé island (Chile). Andean Geology, 43(3), 263-274.
Coren, F., Volpi, V., and Tinivella, U. 2001, Gas hydrate physical properties imaging by multi-attribute analysis-Blake Ridge BSR case history: Marine Geology, 14, 197-210.
1010
Crutchley, G. J., Fraser, D. R. A., Pecher, I. A., Gorman, A. R., Maslen, G., Henrys, S. A. 2015. Gas migration into
1011
gas hydrate bearing sediments on the southern Hikurangi margin of New Zealand. Journal of Geophysical 51
1012
Research: Solid Earth, 120(2), 725-743.
1013
Dallimore, S. R. 2005. Summary and implications of the Mallik 2002 gas hydrate production research well program.
1014
Scientific Results from the Mallik 2002 Gas Hydrate Production Well Program, Mackenzie Delta, Northwest
1015
Territories, Canada, 1-36.
1016
Dallimore, S.R., Collett, T.S., 2005. Scientific results from the Mallik 2002 Gas Hydrate Production Research Well
1017
Program, Mackenzie delta, Northwest Territories. Canada: Geological Survey of Canada Bulletin 585,
1018
CD-ROM, 957 p.
1019 1020
1021
Dong, D., Zhang, G., Zhong, K., Yuan, S., Wu, S. 2009. Tectonic evolution and dynamics of deepwater area of Pearl River Mouth basin, northern South China Sea. Journal of Earth Science, 20(1), 147-159.
Fang, Y. X., Lu, J. A., Liang, J. Q., Kuang, Z. G., Cao, Y. C., Chen, D. F. 2019. Numerical studies of gas hydrate
1022
evolution
1023
https://doi.org/10.1016/j.cngeo.2019.01.001
time
in
the
Shenhu
area
in
the
northern
South
China
Sea.
China
Geology.
1024
Fohrmann, M., Pecher, I. A. 2012. Analysing sand-dominated channel systems for potential gas-hydrate-reservoirs
1025
using an AVO seismic inversion technique on the Southern Hikurangi Margin, New Zealand. Marine and
1026
Petroleum Geology, 38, 19-34.
1027
Fraser, D. R., Gorman, A. R., Pecher, I. A., Crutchley, G. J., Henrys, S. A. 2016. Gas hydrate accumulations related
1028
to focused fluid flow in the Pegasus Basin, southern Hikurangi Margin, New Zealand. Marine and Petroleum
1029
Geology, 77, 399-408.
1030
Fraser, D. 2017. Seismic characterisation of hydrate and shallow gas systems associated with active margin 52
1031
sediments and structures in the Pegasus Basin, Hikurangi Margin, New Zealand (Doctoral dissertation,
1032
University of Otago).
1033
Fu, N., Deng, Y. H., Zhang, G. C., Li, Y. C. 2010. Transitional source rock and its contribution to hydrocarbon
1034
accumulation in superimpose rift-subsidence basin of northern South China Sea: Taking Baiyun sag of Zhu II
1035
depression as an example. Acta Petrolei Sinica, 31(4), 559-565. ( in Chinese with English abstract)
1036 1037
Fu. N., Mi, L. J., Zhang, G. C. 2007. Source rocks and origin of oil and gas in the northern Baiyun Depression of Pearl River Mouth Basin. Acta Petrolei Sinica, 3, 006.
1038
Fujii, T., Suzuki, K., Takayama, T., Tamaki, M., Komatsu, Y., Konno, Y., Yoneda, J., Yamamoto, K., Nagao, J. 2015.
1039
Geological setting and characterization of a methane hydrate reservoir distributed at the first offshore production
1040
test site on the Daini-Atsumi Knoll in the eastern Nankai Trough, Japan. Marine and Petroleum Geology, 66,
1041
310-322.
1042 1043
Gorman, A. R., Holbrook, W. S., Hornbach, M. J., Hackwith, K. L., Lizarralde, D., Pecher, I. 2002. Migration of methane gas through the hydrate stability zone in a low-flux hydrate province. Geology, 30(4), 327-330.
1044
Guan, J. A., Liang, D. 2018. Discussion on the rapid formation mechanism and evolution process of methane
1045
hydrate-bearing sediments in Shenhu Area of northern South China Sea. Marine and Petroleum Geology, 91,
1046
225-235.
1047
Guan, J., Wan, L., Liang, D. 2019. Gauging formation dynamics of structural-seepage methane hydrate reservoirs in
1048
Shenhu area of northern South China Sea: Impact of seafloor sedimentation and assessment of controlling
1049
factors. Marine and Petroleum Geology, 107, 185-197. 53
1050
Guo, Y. Q., Yang, S. X., Liang, J. Q., Lu, J. A., Lin, L., Kuang, Z. G. 2017.Characteristics of high gas hydrate
1051
distribution in the Shenhu area on the northern slope of the South China Sea. Earth Science Frontiers, 24(4),
1052
24-31.( in Chinese with English abstract)
1053 1054
Haacke, R. R., Westbrook, G. K., Hyndman, R. D. 2007. Gas hydrate, fluid flow and free gas: Formation of the bottom-simulating reflector. Earth and Planetary Science Letters, 261(3-4), 407-420.
1055
He, J. X., Chen, S. H., Liu, H. L., Liu, S. L. 2009. Natural gas genetic types and source rocks in the northern slope of
1056
Baiyun Sag to Panyu Low Uplift in Pearl River Mouth Basin. Acta Petrolei Sinica, 30(1), 16-21. ( in Chinese
1057
with English abstract)
1058
He, J. X., Chen, S. H., Ma, W, H., Gong, X. F. 2012. The evolution, migration and accumulation regularity of oil and
1059
gas in Zhujiangkou basin, northern South China Sea. Geology in China, 39(1), 106-118( in Chinese with
1060
English abstract)
1061
He, J. X., Yan, W., Zhu, Y. H., Zhang, W., Gong, F. X., Liu, S. L., Zhang, J. R., Gong, X. F. 2013. Biogeneic and
1062
sub-biogenic gas resource potential and genetic types of natural gas hydrates in the northern marginal basins of
1063
South China Sea. Natural Gas Industry, 33(6):121-134. ( in Chinese with English abstract)
1064 1065
Heggland, R. 1997. Detection of gas migration from a deep source by the use of exploration 3D seismic data. Marine Geology, 137(1-2), 41-47.
1066
Hou, D. J., Pang, X., Xiao, J. X., Zhang, J. C., Shi, H. S., Wang, J. R., Shu, Y., Zhu, J. Z. 2008. Geological and
1067
Geochemical Evidence on the Identification of Natural Gas Migration Through Fault System, Baiyun Sag, Pearl
1068
River Mouth Basin, China. Earth Science Frontiers, 15(4), 81-87. 54
1069 1070
1071
Huang, X., Zhu, Y. H., Lu, Z. Q., Wang, P. K. 2010. Study on genetic types of hydrocarbon gases from the gas hydrate drilling area, the northern South China Sea. Geoscience, 24(3):576-580. ( in Chinese with English abstract)
Hustoft, S., Bünz, S., & Mienert, J. 2010. Three
dimensional seismic analysis of the morphology and spatial
1072
distribution of chimneys beneath the Nyegga pockmark field, offshore mid-Norway. Basin Research, 22(4),
1073
465-480.
1074
Hyndman, R. D., Davis, E. E. 1992. A mechanism for the formation of methane hydrate and seafloor bottom
1075
simulating reflectors by vertical fluid expulsion. Journal of Geophysical Research: Solid Earth, 97(B5),
1076
7025-7041.
1077
Ito, T., Komatsu, Y., Fujii, T., Suzuki, K., Egawa, K., Nakatsuka, Y., Konno, Y., Yoneda, J., Jin, Y., Kida, M., Nagao,
1078
J., Nagao, J. 2015. Lithological features of hydrate-bearing sediments and their relationship with gas hydrate
1079
saturation in the eastern Nankai Trough, Japan. Marine and Petroleum Geology, 66, 368-378.
1080 1081
Judd, A. G., Hovland, M. 1992. The evidence of shallow gas in marine sediments. Continental Shelf Research, 12(10), 1081-1095.
1082
Kang, D. J., Liang, J. Q., Kuang, Z. G., Lu, J. A., Guo, Y. Q., Liang, J. Cai, H. M., Qu, C. W., 2018. Application of
1083
elemental capture spectroscopy logging in hydrate reservoir evaluation in the Shenhu sea area. Natural Gas
1084
Industry, 38, 12, 54-60.
in Chinese with English abstract
1085
Kida, M.; Jin, Y.;Watanabe, M.; Konno, Y.; Yoneda, J.; Egawa, K.; Ito, T.; Nakatsuka, Y.; Suzuki, K.; Fujii, T.,
1086
Nagao, J. 2015.Chemical and crystallographic characterizations of natural gas hydrates recovered from a
1087
production test site in the eastern Nankai Trough. Marine and Petroleum Geology, 66, 396–403. 55
1088
Konno, Y., Fujii, T., Sato, A., Akamine, K., Naiki, M., Masuda, Y., Yamamoto, K., Nagao, J. 2017. Key findings of
1089
the world’s first offshore methane hydrate production test off the coast of Japan: Toward future commercial
1090
production. Energy & Fuels, 31(3), 2607-2616.
1091
Kraemer, L. M., Owen, R. M., Dickens, G. R. 2000. Lithology of the upper gas hydrate zone, Blake Outer Ridge: a
1092
link between diatoms, porosity, and gas hydrate. In Proceedings of the Ocean Drilling Program. Scientific
1093
Results, 164, 229-236, Texas A&M University.
1094 1095 1096 1097
1098 1099
Kumar, J., Sain, K., & Arun, K. P. 2018. Seismic attributes for characterizing gas hydrates: a study from the Mahanadi offshore, India. Marine Geophysical Research, 1-14. Kvenvolden, K. A. 1988. Methane hydrate-a major reservoir of carbon in the shallow geosphere ?. Chemical geology, 71(1-3), 41-51.
Kvenvolden, K. A. 1993. Gas hydrates-geological perspective and global change. Reviews of geophysics, 31(2), 173-187.
1100
Li, J., Lu, J. A., Kang, D., Ning, F., Lu, H., Kuang, Z., Wang, D., Liu, C., Hu, G., Wang, J., Liang, J. 2019a.
1101
Lithological characteristics and hydrocarbon gas sources of gas hydrate-bearing sediments in the Shenhu area,
1102
South China Sea: Implications from the W01B and W02B sites. Marine Geology, 408, 36-47.
1103 1104
Li J F, Ye J L, QIN X W, et al. 2018.The first offshore natural gas hydrate production test in South China Sea. China Geology, 1(1), 5-16.
1105
Li, P. L. 1993. Cenozoic tectonic movement in Pearl River Mouth Basin. China Offshore Oil and Gas, 7(6), 13-17.
1106
Li, P. L., Rao, C. 1994. Tectonic characteristics and evolution history of the Pearl River Mouth Basin. Tectonophysics, 56
1107
235(1-2), 13-25.
1108
Li, Y., Jiang, Z., Liang, S., Zhu, J., Huang, Y., Luan, T. 2015. Hydrocarbon generation in the lacustrine mudstones of
1109
the Wenchang Formation in the Baiyun Sag of the Pearl River Mouth Basin, northern South China Sea. Energy
1110
& Fuels, 30(1), 626-637.
1111
Li, Y. P., Yan, C. Z., Li, J. Shi, W. Y., Chen, L. 2019b.Application of well-free broadband seismic inversion
1112
technology on the description of gas hydrate ore body in Shenhu waters, South China Sea. China Offshore Oil
1113
and Gas, 31 (1), 51-60.
1114
Liang, J. Q., Wang, H. B., Su, X., Fu, S. Y., Wang, L. F., Guo, Y. Q., Chen, F., Shang, J. J. 2014. Na tural gas hydrate
1115
formation conditions and the associated controlling factors in the northern slope of the South China Sea. Natural
1116
Gas Industry, 34 (7), 128-135.( in Chinese with English abstract)
1117
Liang, J. Q., Zhang, Z. J., Su, P. B., Sha, Z. B., Yang, S. X. 2017. Evaluation of gas hydrate-bearing sediments below
1118
the conventional bottom-simulating reflection on the northern slope of the South China Sea. Interpretation, 5, 3,
1119
61-74.
1120 1121
Lin, H. M., Shi, H. S. 2014. Hydrocarbon accumulation conditions and exploration direction of Baiyun-Liwan deep water in the Pearl River Mouth Basin. Natural Gas Industry, 34(5):29-36. ( in Chinese with English abstract)
1122
Liu, B. J., Pang, X., Yan, C. Z., Liu, J., Lian, S. Y., He, M., Shen, J. 2011. Evolution of the Oligocene-Miocene shelf
1123
slope-break zone in the Baiyun deep-water area of the Pearl River Mouth Basin and its significance in oil-gas
1124
exploration. Acta Petrolei Sinica, 32(2), 234-242. ( in Chinese with English abstract)
1125
Liu, C., Meng, Q., Hu, G., Li, C., Sun, J., He, X., Wu, N., Yang, S., Liang, J. 2017. Characterization of 57
1126
hydrate-bearing sediments recovered from the Shenhu area of the South China Sea. Interpretation, 5(3),
1127
SM13-SM23.
1128 1129
1130 1131
1132 1133
Lorenson, T.D., Collett, T.S. 2018. National gas hydrate expedition 01 offshore India; gas hydrate systems as revealed by hydrocarbon gas geochemistry. Marine and Petroleum Geology, 92, 477-492.
Løseth, H., Gading, M., Wensaas, L. 2009. Hydrocarbon leakage interpreted on seismic data. Marine and Petroleum Geology, 26(7), 1304-1319.
Majumdar, U., Cook, A. E., Shedd, W., Frye, M. 2016. The connection between natural gas hydrate and bottom simulating reflectors. Geophysical Research Letters, 43(13), 7044-7051.
1134
Mi, L. J., Zhang, G. C., Shen, H. L., Liu, Z., Guo, R., Zhong, K., Tian, J. X. 2008. Eocene-Lower Oligocene
1135
sedimentation characteristics of Baiyun Sag in the deep water area of Pearl River Mouth Basin. Acta Petrolei
1136
Sinica, 29(1), 29-34. ( in Chinese with English abstract)
1137
Moridis, G. J., Collett, T. S., Dallimore, S. R., Satoh, T., Hancock, S., Weatherill, B. 2004. Numerical studies of gas
1138
production from several CH4 hydrate zones at the Mallik site, Mackenzie Delta, Canada. Journal of petroleum
1139
science and engineering, 43(3-4), 219-238.
1140
Nakajima, T., Kakuwa, Y., Yasudomi, Y., Itaki, T., Motoyama, I., Tomiyama, T., Machiyama, H., katayama, H.,
1141
Okitsu, O., Morita, S., Tanahshi, M., Matsumoto, R. 2014. Formation of pockmarks and submarine canyons
1142
associated with dissociation of gas hydrates on the Joetsu Knoll, eastern margin of the Sea of Japan. Journal of
1143
Asian Earth Sciences, 90, 228-242.
1144
Pang, X., Chen, C. M., Chen, H. H., He, M., Shen, J., Liu, B. J., Wu, X. J.2008.A study on hydrocarbon accumulation 58
1145
dynamics in Baiyun deep-water area, Pearl River Mouth Basin. China Offshore Oil and Gas, 20(1), 9-14. ( in
1146
Chinese with English abstract)
1147 1148
Paganoni, M., Cartwright, J. A., Foschi, M., Shipp, C. R., Rensbergen, P. V. 2016. Structure II gas hydrates found below the bottom-simulating reflector. Geophysical Research Letters, 43, 11, 5696-5706.
1149
Qian, J., Wang, X., Collett, T. S., Guo, Y., Kang, D., & Jin, J. 2018. Downhole log evidence for the coexistence of
1150
structure II gas hydrate and free gas below the bottom simulating reflector in the South China Sea. Marine and
1151
Petroleum Geology, 98, 662-674.
1152
Qiao, S. H., Su, M., Yang, R., Su, P. B., Kuang, Z. G., Liang, J. Q., Wu, N. Y. 2014.A comparative study on the
1153
differences of fluid migration between the Shenhu and LW3-1 drilling areas for natural gas hydrate, northern
1154
South China Sea. Natural Gas Industry, 34(10):137-143. ( in Chinese with English abstract)
1155
Ryu, B. J., Collett, T. S., Riedel, M., Kim, G. Y., Chun, J. H., Bahk, J. J.,Lee, J. Y., Kim, J. H., Yoo, D. G. 2013.
1156
Scientific results of the second gas hydrate drilling expedition in the Ulleung basin (UBGH2). Marine and
1157
Petroleum Geology, 47, 1-20.
1158
Sassen R, Sweet S T, Milkov A V, DeFreitas D A, Kennicutt M C, Roberts H H. 2001. Stability of thermogenic gas
1159
hydrate in the Gulf of Mexico: Constraints on models of climate change. In Paull C K, Dillon W P (Eds).
1160
Natural gas hydrates: Occurrence, Distribution, and Detection, 131-143.
1161 1162
1163
Satyavani, N., Alekhya, G., Sain, K. 2015. Free gas/gas hydrate inference in Krishna–Godavari basin using seismic and well log data. Journal of Natural Gas Science and Engineering, 25, 317-324.
Satyavani, N., Thakur, N. K., Kumar, N. A., & Reddi, S. I. 2005. Migration of methane at the diapir structure of the 59
1164
1165 1166
western continental margin of India insights from seismic data. Marine Geology, 219(1), 19-25.
Schoderbek, D., Boswell, R., 2011. IġnIk Sikumi #1, Gas Hydrate test Well, Successfully Installed on the Alaska north slope. Fire in the Ice Methane Hydrate Newsletter 11, 1-5.
1167
Sha, Z. B., Liang, J. Q., Zhang, G. X., Yang, S. X., Lu, J. A., Zhang, Z. J., McConnell, D. R., Humphrey, G. 2015. A
1168
seepage gas hydrate system in northern South China Sea: Seismic and well log interpretations. Marine Geology,
1169
366, 69-78.
1170 1171
1172 1173
Shankar, U., Sain, K., Riedel, M. 2014. Assessment of gas hydrate stability zone and geothermal modeling of BSR in the Andaman Sea. Journal of Asian Earth Sciences, 79, 358-65.
Shao, L., Pang, X., Qiao, P., Chen, C., Li, Q., Miao, W. 2008. Sedimentary filling of the Pearl River Mouth Basin and its response to the evolution of the Pearl River. Acta Sedimentologica Sinica, 26(2), 179.
1174
Shi, H. S., He, M., Zhang, L. L., Yu, Q. H., Pang, X., Zhong, Z. H., Liu, L. H.2014.Hydrocarbon
1175
geology, accumulation pattern and the next exploration strategy in the east ern Pearl River Mouth basin. China
1176
Offshore Oil and Gas, 26(3), 11-22. ( in Chinese with English abstract)
1177
Shi, H. S., Liu, B. J., Yan, C. Z., Zhu, M., Pang, X., Qin, C. G. 2010. Hydrocarbon accumulation conditions and
1178
exploration potential in Baiyun-Liwan deepwater area, Pearl River Mouth Basin. China Offshore Oil and Gas,
1179
22(6), 369-374.( in Chinese with English abstract)
1180
Shi, H. S., Qin, C. G., Zhang, Z. T., Xuan, Y. H. 2009a. A Discussion on the Complex Hydrocarbon Transport System
1181
in the North Slope of Baiyun sag-Panyu Low Uplift, Pearl River Mouth Basin. China Offshore Oil and Gas,
1182
21(6), 361-366. ( in Chinese with English abstract) 60
1183
Shi, W. Z., Song, Z. F., Wang, X. L., Kong, M. 2009b. Diapir structure and its origin in the Baiyun Depression, Pearl
1184
River Mouth Bsin, China. Earth Science-Journal of China University of Geosciences, 34(5), 778-784. ( in
1185
Chinese with English abstract)
1186
Sloan E D. 1998. Clathrate Hydrates of Natural Gas. New York: Marced Dekker, 726.
1187
Su, M., Alves, T. M., Li, W., Sha, Z., Hsiung, K. H., Liang, J., Kuang, Z., Wu, N., Zhang, B., Chiang, C. S. 2019.
1188
Reassessing two contrasting Late Miocene-Holocene stratigraphic frameworks for the Pearl River Mouth Basin,
1189
northern South China Sea. Marine and Petroleum Geology, 102, 899-913.
1190
Su, M., Sha, Z. B., Zhang, C. M., Wang, H. B., Wu, N. Y., Yang, R., Liang, J. Q., Qiao, S. H., Cong, X. R., Liu, J. 2017.
1191
Types, Characteristics and Significances of Migrating Pathways of Gas bearing Fluids in the Shenhu Area,
1192
Northern Continental Slope of the South China Sea. Acta Geologica Sinica (English Edition), 91(1), 219-231.
1193
Su, M., Yang, R., Wang, H. B., Sha, Z.B., Liang, J. Q., Wu, N. Y., Qiao, S. H., Cong, X. R. 2016. Gas hydrates
1194
distribution in the Shenhu Area, northern South China Sea: comparisons between the eight drilling sites with
1195
gas-hydrate petroleum system. Geologica Acta, 14(2): 79-100.
1196
Su, M., Yang, R., Wu, N. Y., Wang, H. B., Liang, J. Q., Sha, Z. B.,Cong, X. R., Qiao, S. H. 2014a. Structural
1197
characteristics and the influences on gas hydrate in Shenhu Area in northern continental slope of the South
1198
China Sea. Acta Geologica Sinica, 88(3), 318-326. ( in Chinese with English abstract)
1199
Su, P. B., Liang, J.Q., Sha, Z. B., Fu, S. Y. 2014b. Gas sources condition of gas hydrate formation in Shenhu deep
1200
water sea zone. Journal of Southwest Petroleum University (Science & Technology Edition), 36(2), 1-8. ( in
1201
Chinese with English abstract) 61
1202
Su, P., Liang, J., Peng, J., Zhang, W., Xu, J. 2018. Petroleum systems modeling on gas hydrate of the first
1203
experimental exploitation region in the Shenhu area, northern South China sea. Journal of Asian Earth Sciences,
1204
168, 57-76.
1205
Tréhu, A. M., Long, P. E., Torres, M. E., Bohrmann, G., Rack, F. R., Collett, T. S., Goldberg, D. S., Milkov, A. V.,
1206
Riedel, M., Schultheiss, P., Bangs, N. L., Barr, S. R., Borowski, W. S., Claypool, G. E., Delwiche, M. E.,
1207
Dickens, G. R., Gracia, E., Guerin, G., Holland, M., Johnson, J. E., Lee, Y,-J., Liu, C,-S., Su, X., Teichert, B.,
1208
Tomaru, H., Vanneste, M., Watanabe,M., Weinberger, J. L. 2004a. Three-dimensional distribution of gas hydrate
1209
beneath southern Hydrate Ridge: constraints from ODP Leg 204. Earth and Planetary Science Letters, 222(3),
1210
845-862.
1211
Tréhu, A.M., Bohrmann, G., Rack, F.R.2004b. Expedition 204 Scientists, Proceedings of the Ocean Drilling
1212
Program: Volume 204 Initial Reports, Drilling Gas Hydrates on Hydrate Ridge, Cascadia Continental Margin,
1213
Washington,
1214
204_IR/front.htm.
1215 1216
DC:
IODC
Management
International,
Inc.,
http://www-odp.tamu.edu/publications/
Vanneste, M., De Batist, M., Golmshtok, A., Kremlev, A., Versteeg, W. 2001. Multi frequency seismic study of gas hydrate-bearing sediments in Lake Baikal, Siberia. Marine Geology, 172, 1-21.
1217
Wang, J., Wu, S., Kong, X., Li, Q., Wang, J., Ding, R. 2018. Geophysical characterization of a fine-grained gas
1218
hydrate reservoir in the Shenhu area, northern South China Sea: Integration of seismic data and downhole logs.
1219
Marine and Petroleum Geology, 92, 895-903.
1220 1221
Wang, S. H., Yan, W., Song, H. B. 2006. Mapping the thickness of the gas hydrate stability zone in the South China Sea. Terrestrial Atmospheric and Oceanic Sciences, 17(4), 815. 62
1222
Wang, X.J., Collett, T. S., Lee, M. W., Yang, S. X., Guo, Y. Q., Wu, S. G. 2014. Geological controls on the occurrence
1223
of gas hydrate from core, downhole log, and seismic data in the Shenhu area, South China Sea. Marine Geology,
1224
357, 272-292.
1225 1226
1227 1228
1229 1230
Wang, X., Pan, D. 2017. Application of AVO attribute inversion technology to gas hydrate identification in the Shenhu Area, South China Sea. Marine and Petroleum Geology, 80, 23-31.
Wang, J., Wu, S., Yao, Y. 2018. Quantifying gas hydrate from microbial methane in the South China Sea. Journal of Asian Earth Sciences, 168, 48-56.
Wei, J., Fang, Y., Lu, H., Lu, H., Lu, J., Liang, J., Yang, S. 2018. Distribution and characteristics of natural gas hydrates in the Shenhu Sea Area, South China Sea. Marine and Petroleum Geology, 98, 622-628.
1231
Wei, J., Liang, J., Lu, J., Zhang, W., He, Y. 2019. Characteristics and dynamics of gas hydrate systems in the
1232
northwestern South China Sea-Results of the fifth gas hydrate drilling expedition. Marine and Petroleum
1233
Geology, 110, 287-298.
1234
Wu, N. Y., Yang, S. X., Wang, H. B., Liang, J. Q., Gong, Y. H. Lu, Z. Q., Wu, D. D., Guan, H. X. 2009. Gas bearing
1235
fluid influx sub-system for gas hydrate geological system in Shenhu Area. Northern South China Sea. Chinese
1236
Journal of Geophysics, 52(6),1 641- 1650. ( in Chinese with English abstract)
1237
Wu, N.Y., Yang, S.X., Zhang, H.Q., Liang, J.Q., Wang, H.B., Lu, J. A. 2010. Gas hydrate system of Shenhu area,
1238
northern South China Sea: Wire-line logging, geochemical results and preliminary resources estimates. In
1239
Offshore technology conference. Offshore Technology Conference.
1240
Wu, N.Y., Zhang, H. Q., Yang, S. X., Zhang, G.X., Liang, J. Q., Lu, J. A., Su, X., Schultheiss, P., Holland, M., Zhu, Y. 63
1241
H. 2011. Gas hydrate system of Shenhu area, northern South China Sea: geochemical results. Journal of
1242
Geological Research, 2011, 1-10.
1243 1244
Wu, S. G., Zhang, G. X., Huang, Y. Y., Liang, J., Wong, H. K. 2005. Gas hydrate occurrence on the continental slope of the northern South China Sea. Marine and Petroleum Geology, 22(3), 403-412.
1245
Xie, H., Zhou, D., Pang, X., Li, Y., Wu, X., Qiu, N., Li, P. C., Chen, G.H. 2013. Cenozoic sedimentary evolution of
1246
deepwater sags in the Pearl River Mouth Basin, northern South China Sea. Marine Geophysical Research,
1247
34(3-4), 159-173.
1248
Xiong, P., Lu, H., Xie, X., Zhang, G., Fu, S., Jiang, L., Zhang, P. 2019. Geochemical responses and implications for
1249
gas hydrate accumulation: Case study from site SHC in Shenhu Area within northern South China Sea. Marine
1250
and Petroleum Geology.
1251 1252
Xue, H., Du, M.,Wen, P. F.,Zhang, B, J., Zhang, R. W 2017.The application of grid tomography method to quasi three dimensional of Xisha hydrate. Geophysical and Geochemical Exploration,41(5), 846-851
1253
Yamamoto, K., Wang, X. X., Tamaki, M., & Suzuki, K. 2019. The second offshore production of methane hydrate in
1254
the Nankai Trough and gas production behavior from a heterogeneous methane hydrate reservoir. RSC
1255
Advances, 9(45), 25987-26013.
1256
Yang, J. X., Wang, X. J., Jin, J. P., Li, Y. P., Li, J., Qian, J., Shi, H. S., Zhang, G. X. 2017a. The role of fluid migration
1257
in the occurrence of shallow gas and gas hydrates in the south of the Pearl River Mouth Basin, South China Sea.
1258
Interpretation, 5(3), SM1-SM11.
1259
Yang, S. X., Zhang, M., Liang, J. Q., Lu, J.A., Zhang, Z.J., Melanie, H., Peter, S., Fu, S. Y., Sha, Z. B., and the 64
1260
GMGS3 Science Team. 2015. Preliminary Results of China’s Third Gas Hydrate Drilling Expedition: A Critical
1261
Step From Discovery to Development in the South China Sea. Fire in the Ice, 15, 2, 1-5.
1262
Yang, S. X., Liang, J. Q., Lu, J. A., Qu C. W., Liu, B. 2017b.New understandings on the characteristics and
1263
controlling factors of gas hydrate reservoirs in the Shenhu area on the northern slope of the South China Sea.
1264
Earth Science Frontiers, 24(4), 1-14. ( in Chinese with English abstract)
1265
Yang, S .X, Liang, J. Q, Lei, Y., Gong, Y. H., Xu, H. N., Wang, H. B., Lu, J. A., Holland, M., Schultheiss, P., Wei, J.
1266
G., and the GMGS4 Science Team. 2017c. GMGS4 Gas Hydrate Drilling Expedition in the South China Sea.
1267
Fire in the Ice: Methane Hydrate Newsletter, 17(1), 7-11.
1268
Yang, S. X., Lei, Y., Liang, J. Q., Holland, M., Schultheiss, P., Lu, J. A., Wei, J. G. 2017d. Concentrated Gas
1269
Hydrate in the Shenhu Area, South China Sea: Results From Drilling Expeditions GMGS3 & GMGS4. In
1270
Proceedings of 9th International Conference on Gas Hydrates, Denver, Paper No. 105.
1271
Yang, S. X., Zhang, H. Q., Wu, N. Y., Su, X., Schultheiss, P., Holland, M., Zhang, G. X., Liang, J. Q., Lu, J. A., Rose,
1272
K. 2008. High concentration hydrate in disseminated forms obtained in Shenhu area, North Slope of South
1273
China Sea. Proceedings of the 6th International Conference on Gas Hydrate (ICGH2008), Vancouver, British
1274
Columbia, Canada.
1275
Ye J.L., Qin, X.W., Qiu, H.J., Xie, W. W., Lu, H.F., Lu, C., Zhou, J.H., Liu, J.Y., Yang, T.B., Cao, J., Sa, R.N.2018.
1276
Data Report: Molecular and Isotopic composition of the extracted gas from China’s first offshore national gas
1277
hydrate production test in South China Sea. Energies, 11, 2793; dio: 10.3390/en11102793.
1278
Ye, J., Wei, J., Liang, J., Lu, J., Lu, H., & Zhang, W. 2019. Complex gas hydrate system in a gas chimney, South 65
1279
China Sea. Marine and Petroleum Geology, 104, 29-39.
1280
Yu, S. M., Mei, L. F., Shi, H. S., Qin, C. G., Tang, J. G. 2007. Relationship between faults and hydrocarbon
1281
accumulation in Panyu low massif and north slope of Bai yun Sag, Pearl River Mouth Basin. Petroleum
1282
Exploration and Development, 34(5), 562-579. ( in Chinese with English abstract)
1283
Zhang, G. C., Yang, H. C., Chen, Y., Ji, M., Wang, K., Yang, D. S., Han, X. Y., Sun, Y. H. 2014. The Baiyun Sag: A
1284
giant rich gas-generation sag in the deepwater area of the Pearl River Mouth Basin. Natural Gas Industry,
1285
34(11):11-25. ( in Chinese with English abstract)
1286 1287
Zhang, G. X., Huang, Y. Y., Zhu, Y. H., & Wu, B. H. 2002. Prospect of gas hydrate resources in the South China Sea. Marine Geology and Quaternary Geology, 22(1), 75-82.( in Chinese with English abstract)
1288
Zhang, G. X., Liang, J. Q., Lu, J. A., Yang, S. X., Zhang, M., Holland, M., Schultheiss, P., Su, X., Sha, Z. B., Xu, H.
1289
N., Gong, Y. H., Fu, S. Y., Wang, L. F., Kuang, Z. G. 2015. Geological features, controlling factors and potential
1290
prospects of the gas hydrate occurrence in the east part of the Pearl River Mouth Basin, South China Sea. Marine
1291
and Petroleum Geology, 67, 356-367.
1292
Zhang, H. Q., Yang, S. X., Wu, N. Y. 2007. GMGS-1 science team: China's first gas hydrate expedition successful
1293
(No. 1). Fire in the Ice: Methane Hydrate Newsletter, National Energy Technology Laboratory, US Department
1294
of Energy, Spring/Summer.
1295
Zhang, W., Liang, J. Q., He, J. X., Cong, X. R., Su, P. B., Lin, L., Liang, J. 2018a.Differences in natural gas hydrate
1296
migration and accumulation between GMGS1 and GMGS3 drilling areas in the Shenhu Area, northern South
1297
China Sea. Natural Gas Industry, 38(3):138-149. ( in Chinese with English abstract) 66
1298
Zhang, W., Liang, J. Q., Su, P. B., Wei, J. G., Sha, Z. B., Lin, L., Liang, J., Huang ,W. 2018b. Migration pathways of
1299
hydrocarbons and their controlling effects associated with high saturation gas hydrate in Shenhu area, northern
1300
South China Sea. Geology in China, 45(1), 1-14. ( in Chinese with English abstract)
1301 1302
Zhang, R. W., Lu, J. A., Wen, P. F., Kuang, Z. G., Zhang, B. J., Xue, H., Xu, Y. X., Chen, X. 2018c. Distribution of gas hydrate reservoir in the first production test region of the Shenhu. China Geology, 4, 493-504.
1303
Zhang, W., Liang, J.Q., Lu, J. A., We, J. G., Su, P. B., Fang, Y. X., Guo, Y. Q., Yang, S. X., Zhang, G. X. 2017.
1304
Accumulation features and mechanisms of high saturation natural gas hydrate in Shenhu Area, northern South
1305
China Sea. Petroleum Exploration and Development, 44(5), 708-719.
1306
Zhang, W., Liang, J., Wei, J., Su, P., Lin, L., Huang, W. 2019. Origin of natural gases and associated gas hydrates in
1307
the Shenhu area, northern South China Sea: Results from the China Gas Hydrate Drilling Expeditions. Journal
1308
of Asian Earth Sciences, 103953.
1309 1310
Zhong, J. Q. 1994. Characteristics of geologic structure and basin evolution in Pearl River Mouth Basin. Transaction of Oceanology and Limnology, 1.
1311
Zhong, Z. H., Shi, H. S., Zhu, M., Pang, X., He, M., Zhao, Z. X., Liu, S. Q., Wang, F. 2014.A discussion on the
1312
tectonic-stratigraphic framework and its origin mechanism in Pearl River Mouth basin. China Offshore Oil and
1313
Gas, 5, 20-29. ( in Chinese with English abstract)
1314
Zhong, G., Liang, J., Guo, Y., Kuang, Z., Su, P., Lin, L. 2017. Integrated core-log facies analysis and depositional
1315
model of the gas hydrate-bearing sediments in the northeastern continental slope, South China Sea. Marine and
1316
Petroleum Geology, 86, 1159-1172. 67
1317
Zhu, J. Z., Shi, H. S., He, M., Pang, X., Yang, S. K., & Li, Z. W. 2008. Origins and geochemical characteristics of
1318
gases in LW3-1-1 well in the deep sea region of Baiyun Sag, Pearl River Mouth Basin. Natural Gas Geoscience,
1319
19(2), 229-233. ( in Chinese with English abstract)
1320
Zhu, J. Z., Shi, H. S., Pang, X., Zhang, Z. L., Long, Z. L., Liu, B. J., Shi, Y. 2012. Discussion on natural gas
1321
generation and giant-medium size gas field formation in Baiyun sag. Natural Gas Geoscience, 23(2), 213-221.
1322
( in Chinese with English abstract)
1323
Zhu, W., Huang, B., Mi, L., Wilkins, R. W., Fu, N., & Xiao, X. 2009. Geochemistry, origin, and deep-water
1324
exploration potential of natural gases in the Pearl River Mouth and Qiongdongnan basins, South China Sea.
1325
AAPG bulletin, 93(6), 741-761.
1326
Zhu, Y. H., Huang, X., Fu, S. Y., Su, P. B. 2013. Gas sources of natural gas hydrates in the Shenhu Drilling Area,
1327
South China Sea: geochemical evidence and geological analysis. Acta Geologica Sinica (English Edition), 87(3),
1328
767-776.
1329 1330
Zillmer, M., Flueh, E. R., Petersen, J. 2005. Seismic investigation of a bottom simulating reflector and quantification of gas hydrate in the Black Sea. Geophysical Journal International, 161(3), 662-678.
68
1331
Figure and table captions
1332
Fig. 1. (A) Geographical location of the Shenhu area in the Pearl River Mouth Basin (PRMB) of
1333
the northern South China Sea (SCS) (modified from Su et al., 2019). (B) Bathymetric map and
1334
distribution of the gas-hydrate drilling and coring sites (after Yang et al., 2017c, 2017d). The
1335
gas-hydrate drilling areas of the GMGS1 (purple dashed frame) and GMGS3 and 4 (blue dashed frame)
1336
expeditions are located in the submarine canyon systems in the northern slope of the Baiyun Sag (after
1337
Yang et al., 2017c; Su et al., 2019). The distribution of the main drilling and coring sites is primarily
1338
located at the structural highs or on the edge of the seafloor ridges. The gas-hydrate production test
1339
region (GHPTR) is located in the southwestern part of the GMGS3 and 4 drilling areas. Two ridges, the
1340
western and eastern ridges, cross the GHPTR. The drilling and coring sites studied in this paper are
1341
located at the top of these two ridges. (QDNB = Qiongdongnan Basin).
1342
1343 1344
Fig. 2. Structural evolution characteristics and stratigraphic column of the Pearl River Mouth Basin (modified from Pang et al., 2008 and Zhang et al., 2019).
1345
1346
Fig. 3. Integrated seismic profiles of the drilling and coring sites in the Shenhu area. Green and
1347
black solid lines indicate the positions of drilling wells. Black dotted lines indicate faults. Position of
1348
the connecting-well seismic line is shown in Figure 1B. (GC = gas chimney, BZ = blanking zone, ERs
1349
= enhanced reflections).
69
1350
Fig. 4. Seismic reflection and interpretation profile of site W11 in the gas-hydrate production test
1351
region. (A) Distinct BSR showing strong amplitude reflections, and the inclined strong seismic
1352
reflections connecting the BSR. Acoustic blanking zones (BZs) are present both above and below the
1353
high amplitudes around the BSR. Several high-angle faults and accompanying enhanced reflections
1354
(ERs) and pull-down features were interpreted below the drilling site. (B) Enlarged section showing
1355
features of enhanced reflections distributed just below the BSR, indicating the presence of free gas
1356
(position of seismic line is shown in Figure 1B).
1357
1358
Fig. 5. Seismic reflection and interpretation profile of site W17 in the gas-hydrate production test
1359
region. (A) The BSR shows strong amplitude reflections crosscutting the strata. Its polarity is opposite
1360
to that of the seafloor. Acoustic blanking zones (BZs) appear both above and below high amplitudes
1361
around the BSR. Amplitude anomalies, including acoustic masking and chaotic features accompanied
1362
by enhanced reflections (ERs) and pull-down features, are also present below the drilling site. Several
1363
high-angle faults developed below the BSR are interpreted. (B) Enlarged section showing features of
1364
obliquely enhanced reflections distributed just below the BSR, indicating accumulation of free gas
1365
(position of seismic line is shown in Figure 1B).
1366
1367
Fig. 6. Seismic reflection and interpretation profile of site W18 in the gas-hydrate production test
1368
region. (A) The BSR shows strong amplitude reflections crosscutting the strata and parallel to the
1369
seafloor. Gliding faults extending to the seafloor are recognized in the up-dip direction of the BSR. A 70
1370
significant range of acoustic blanking (BZ), masking, and chaotic features are present below the BSR.
1371
(B) Enlarged section showing features of enhanced reflections (ERs) distributed just below the BSR,
1372
indicating accumulation of free gas (position of seismic line is shown in Figure 1B).
1373
1374
Fig. 7. Seismic reflection and interpretation profile of site W19 in the gas-hydrate production test
1375
region. (A) Seismic characteristics of site W19 are very similar to those of site W18, in which a distinct
1376
BSR and accompanying gliding faults are interpreted. Acoustic blanking (BZ), masking, and enhanced
1377
reflections (ERs) are also present in the drilling site (Zhang et al., 2017). (B) Enlarged section showing
1378
features of enhanced reflections, indicating accumulation of free gas distributed just below the BSR
1379
(position of seismic line is shown in Figure 1B).
1380
1381
Fig. 8. Characteristics of pilot hole with the logging-while-drilling (LWD) curves for drilling sites
1382
in the gas-hydrate production test region (after Guo et al., 2017; Yang et al., 2017d; Zhang et al., 2017).
1383
The gas–hydrate bearing zones (GHBZs) were cored and sampled based on logging anomalies, which
1384
have a high apparent resistivity, low acoustic travel-time difference, relatively low density, and low
1385
natural gamma ray value. (A) site W11, (B) site W17, (C) site W18, and (D) site W19.
1386
1387
Fig. 9. Core observation, lithologic description, and distribution of the gas hydrates confirmed
1388
using coring, thermal imaging, and logging data at (A) site W11 and (B) site W17. No core was 71
1389
available within some sections because drilling sites were conventionally cored with spaced out spot
1390
cores with pressure coring tools, and some of the core lines containing hydrates were cut off and
1391
preserved in liquid nitrogen. Gas inflation cracks and low thermal anomalies with purple or
1392
deep-purple layers indicate presence of gas hydrates. (mbsf= meters below seafloor)
1393
1394
Fig. 10. Core observation, lithologic description, and distribution of gas hydrates confirmed using
1395
coring, thermal imaging, and logging data at (A) site W18 and (B) site W19. No core is available
1396
within some sections because drilling sites were conventionally cored with spaced out spot cores with
1397
pressure coring tools, and some of the core lines containing hydrates were cut off and preserved in
1398
liquid nitrogen. Gas inflation cracks and low thermal anomalies with purple or deep-purple layers
1399
indicate presence of gas hydrates. Thermal image of site W19 is modified from Zhang et al., 2017.
1400
(mbsf= meters below seafloor)
1401
1402
Fig. 11. Characteristics of hydrate cores recovered from coring sites within gas-hydrate
1403
production test region. (A & B) Cavity (116–117 mbsf) and inflation phenomena (120–121 mbsf)
1404
caused by gas-hydrate decomposition at site W11. (C) Porridge-like features resulting from
1405
decomposition of hydrates (139–142 mbsf) at site W11. (D) Significant number of massive hydrates
1406
observed near wellhead at site W17 during drilling process. (E) Porridge-like features resulting from
1407
decomposition of hydrates (238–241 mbsf) at site W17 (after Zhang et al., 2018b). (F) Honeycomb
1408
and porridge-like features resulting from decomposition of hydrates (152–155 mbsf) at site W18. (G) 72
1409
Hydrates (155–158 mbsf) accumulated in clayey silt reservoirs with dispersed morphology and
1410
low-temperature characteristics at site W18. (H) Cavity phenomenon caused by decomposition of
1411
hydrates (165.5–168.5 mbsf) at site W18. (I & J) Strong inflation phenomenon and mushy features
1412
resulting from dissociation of gas hydrates (140–142 mbsf) at site W19 (after Zhang et al., 2017). (K)
1413
Foraminifera fossils recovered from gas-hydrate-bearing section of cores from site W19.
1414
1415
Fig. 12. Lithology, sediment composition, and grain size analysis results of gas-hydrate
1416
host-sediments from coring sites in gas-hydrate production test region in the Shenhu area. (A) site W11,
1417
(B) site W17, (C) site W18, and (D) site W19. Mz (Φ) is medium grain size. GHBZ = gas-hydrate
1418
bearing zone.
1419
1420
Fig. 13. Vertical variation in foraminifera, CaCO3, sand, and porosity of core sediments from
1421
coring sites (A) W18 and (B) W19 in gas-hydrate production test region in the Shenhu area. GHBZ =
1422
gas-hydrate bearing zone.
1423
1424
Fig. 14. Distribution characteristics of free gas with relatively low sedimentary velocities below
1425
gas-hydrate stability zone with relatively high sedimentary velocities in gas-hydrate production test
1426
region in the Shenhu area.
1427 73
1428
Fig. 15. p-wave impedance inversion profile showing distribution characteristics of gas hydrate
1429
and underlying free gas in gas-hydrate production test region in the Shenhu area. Generally, free gas
1430
has a relatively low p-wave impedance below gas-hydrate bearing zone, which has a high p-wave
1431
impedance. Inversion wave impedance is consistent with variation trend of borehole p-wave
1432
impedance curve.
1433
1434
Fig. 16. Calculation results of gas-hydrate stability zone conducted using CSMHYD program
1435
(Sloan, 1998) based on in situ temperature measurements (solid black dots) and different
1436
hydrate-bound gas compositions from the GMGS3 drilling and coring sites (Zhang et al., 2019).
1437
Gas-hydrate saturations calculated from pore-water analysis and pressure core degassing for coring
1438
sites in gas-hydrate production test region in the Shenhu area are from Yang et al. (2017d) and Guo et
1439
al. (2017). Orange, green, and blue dashed lines represent the top of the resistivity anomaly, base of
1440
methane hydrate stability, and base of resistivity anomaly, respectively. (A) site W11, (B) site W17, (C)
1441
site W18, and (D) site W19. (mbsl= meters below sea level; mbsf= meters below seafloor.)
1442
1443 1444
Fig. 17. Synthetic seismograms constructed based on LWD and seismic data acquired from site W11.
1445
1446
Fig. 18. Synthetic seismograms constructed based on LWD and seismic data acquired from site 74
1447
W18.
1448
1449
Fig. 19. Distribution of gas-hydrate-bearing zones (GHBZ) and free-gas-bearing zones (FGBZ)
1450
identified from acoustic travel-time difference, density, and compensated neutron-three porosity log
1451
intersection. (A) site W11, (B) site W17, (C) site W18, and (D) site W19.
1452
1453
Fig. 20. Seismic characteristics of various types of hydrocarbon migration pathways and their
1454
coupling relationships with gas-hydrate stability zones in gas-hydrate production test region. (A)
1455
Acoustic blanking (BZ) and masking reflections below the BSR at sites W11 and W17. Pull-up
1456
features are present in the lower part of this abnormal reflection zone, suggesting the upward piercing
1457
of a mud diapir. Seismic events in upper part of abnormal reflection zone show pull-down
1458
characteristics. A suspected gas chimney is also interpreted near mud diapir. Pull-downs and enhanced
1459
reflections (ERs) suggest presence of gas (Loseth et al., 2009). (B) Distinct low-frequency zone on
1460
instantaneous frequency image, indicating charging and trapping of free gas in sediments (Zhang et al.,
1461
2018b). (C) Large range of acoustic masking and chaotic reflections below sites W18 and W19.
1462
Pull-up features are present in lower part of this abnormal reflection zone, suggesting the upward
1463
piercing of mud diapir. (D) Prominent low-frequency characteristics are also present in instantaneous
1464
frequency image, suggesting intense activity of hydrocarbons transported by mud diapirs from the
1465
deep to shallow. White curved arrows represent possible gas-bearing fluid migration.
75
1466
Table 1. Characteristics of gas hydrates recovered from drilling and coring sites in gas-hydrate
1467
production test region in the Shenhu area. (mbsl= meters below sea level, mbsf=meters below seafloor,
1468
LWD= logging while drilling, BSR= bottom simulating reflector, ERs= enhanced reflections, BZ=
1469
blanking zone.)
1470
1471
Table 2. In situ temperature measurements and geothermal gradients of drilling sites in
1472
gas-hydrate production test region in the Shenhu area. (mbsl= meters below sea level; mbsf= meters
1473
below seafloor.)
76
Table 1. Characteristics of gas hydrates recovered from drilling and coring sites in gas-hydrate production test region in the Shenhu area. (mbsl= meters below sea level, mbsf=meters below seafloor, LWD= logging while drilling, BSR= bottom simulating reflector, ERs= enhanced reflections, BZ= blanking zone.) Site
Water
Total
Depth
Depth
Depth of
Base of
Depth of
Thickness
Maximum
Average
Reservoir
Reservoir
Gas source
Indicators of
depth
drilling
of
of the
the SII
the LWD
the
of gas
gas
gas
porosity
permeability
indicated
gas
depth
BSR
from C1/C2
migration
SI
hydrate
electrical
hydrate
hydrate
hydrate
hydrate
hydrate
(99%C1
resistivity
layer
layer
saturation
saturation
(100%
+0.5%C
anomaly
confirmed
C1)
2+0.5%
and hydrate accumulation
by cores
C3) W11
(mbsl)
(mbsf)
(mbsf)
(mbsf)
(mbsf)
(mbsf)
(mbsf)
(m)
(%)
(%)
(%)
(mD)
1309.75
~222
~200
194
220
202
116.5-192
76
53
34
34.5
0.22
.5
Biogenic
BSR, ERs,
and Mixed
BZ, and faults
W17
1259.00
~315
~230
239
270
270
209-265
56
76
33
33.2
0.32
Biogenic
BSR, ERs,
and Mixed
BZ, pull-down, and faults
W18
1285.41
~234
~171
161
189
174
147-172
25
63
25
56.7
100
Thermoge
BSR, ERs,
nic and
BZ, and
Mixed
acoustic masking
W19
1273.80
~240
~170
165
192
185
135-157.5
22.5
71
45
48.3
5.5
Thermoge
BSR, ERs,
nic and
BZ, and
Mixed
acoustic masking
Table 2. In situ temperature measurements and geothermal gradients of drilling sites in gas-hydrate production test region in the Shenhu area. (mbsl= meters below sea level; mbsf= meters below seafloor.)
Site W11
Water depth mbsl 1309.75
w17
1259.00
W18
1285.41
W19
1273.80
Measured depth mbsf 48.00 95.00 188.00 123.00 206.00 258.10 54.00 121.00 159.50 63.00 107.00 150.50 171.00
Temperature 7.46 10.07 15.11 10.19 13.98 16.17 8.01 12.56 14.61 9.14 11.88 14.25 15.20
Geothermal gradient /100m 5.46
4.43
6.26
5.56
Highlights
Gas hydrate petroleum system of the China first offshore hydrate production test region is investigated. Gas hydrate and underlying free gas are evaluated based on velocity and acoustic impedance inversion. The BSR represents a transitional indicator of structure I and structure II gas hydrate. Presence of foraminifera is not a prerequisite for the emergence of high-saturation hydrates.
Author Contribution Statement
Wei Zhang: Writing- Reviewing and Editing, Conceptualization,Visualization Jinqiang Liang: Investigation,Supervision,Project administration Jiangong Wei: Conceptualization,Investigation,Visualization Jing’an Lu: Investigation,Supervision,Project administration Pibo Su: Resources,Investigation Lin Lin: Software,Methodology Wei Huang: Formal analysis,Resources Yiqun Guo: Methodology,Investigation Wei Deng: Software Xiaolu Yang: Writing - Original Draft Zhifeng Wan: Supervision, Original Draft, Reviewing and Editing.
Declaration of interests ☒ The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper. ☒The authors declare the following financial interests/personal relationships which may be considered as potential competing interests:
Wei Zhang, Jinqiang Liang, Jiangong Wei, Jing’an Lu, Pibo Su, Lin Lin, Wei Huang, Yiqun Guo, Wei Deng, Xiaolu Yang, Zhifeng Wan