- Email: [email protected]
Explosion-proof motor for barrel pumping
QUIPMENT NEWS
over the past two years the preferred option of users has been to convert existing equipment installations to achieve greater throughput. Contact: Richard Bushell, Warman International Ltd., 1 Marden Street, Attarmon NSW 2064, Australia. Tel: +61 2 9934 5100.
New line of plastic pumps Warren Rupp, Inc has launched an entirely new line of nonmetal Sandpiper II TM pumps. Models are available in sizes from 44 inch to 3 inch, with a maximum flow of 223 gal/min (844 l/min). All pumps in the new line have a rugged, bolted design. V-band clamps are not used. This results in a much stronger construction, and easier maintenance. The new pumps also feature the latest design of lubricantfree, non-stall air valve, which is more energy efficient than ever. ESADS+Plus@,the externally serviceable air distribution system, carries a money-back guarantee. The modular air valve has no close-fitting components and is very tolerant of dirty or wet compressed air. Ideal for pumping aggressive chemicals, the new plastic pumps are offered in PVDF or polypropylene, with Santoprene@’ or Teflon@ diaphragms and ball valves. Spill containment, leak detection and pulse output interface options are available for all models. Air valve, check valve cartridges and manifolds are modular in design and completely in-line serviceable.The new line provides unprecedented interchangeability of parts from model to model. Contact: Kimberlin RossPolito, Warren Rupp, lnc, PO Box 1566 Mansfield, OH 44901, USA. Tel: +l 419 524 6366; Fax: +l 419 522 7667; e-mail: [email protected]
WORLD
PUMPS
DECEMBER
1999
Multistage pump offers reduced life cycle costs Sterling Fluid Systems Limited has extended its range of modular multistage pumps with the introduction of the new Sterling multi pump. The multi range offers horizontal ring-section multistage centrifugal pumps ideal for high-pressure applications. Designed to meet the technical requirements of IS0 5199/EN 25199, the key to the success of the multi range is the adoption of an advanced modular design combined with a reduced number of parts and maximum interchangeability. Optimal selection of the impeller diameter combined with the diffuser geometry ensures the pump can be matched to the most demanding of duty requirements. In addition, the innovative design promotes reduced life cycle costs notably through the enhanced efficiency of the patented balance drum design. Avoiding tight, wear-sensitive clearances, the system incorporates a throttling device in order to control flow through the balancing line. Only one shaft seal maximises reliability whilst simple dismantling and reassembly provides a further maintenance bonus. Other special design features include a first stage impeller that ensures reliable operation with low NPSH conditions and the ability to mount the suction casing axially or radially. Contact: Sterling Fluid Systems Limited, Theale Cross, Reading, Berkshire RG31 7SP, UK Tel: +44 118 932 3123; Fax: +44 118 932 3302.
New-for-old deal for slurry pumps Svedala Ltd’s Regional Service Centres are introducing a service exchange programme for their heavy duty slurry pumps.
Customers can purchase a fully factory-refurbished Svedala slurry pump at a competitive price, in exchange for their existing worn Svedala Orion or HM pump, in all pump sizes from 50 mm (2 inch) to 200 mm (8 inch). The pumps are rebuilt in-house at the Service Centres by trained maintenance personnel, who bring the units back to within original, as-new manufactured tolerances. Each refurbished pump is backed by a 6-month warranty, and removal of the worn pump and installation of the exchange unit can also be carried out by the Service Centre for a nominal cost. In addition, the scheme will overcome problems of disposing of disused pumping equipment experienced by customers working towards the new environmental standard IS01 4000, since Svedala will effectively be offering a recycling service. Contact: Paul Beddows, Svedala UK Tel: +44 1788 532100.
Explosion-proof motor for barrel pumping Flux Pumps has introduced a new version of its Type 460 pump motor, with variable speed control. Flux claims its ~460 Ex is currently the only explosion-proof motor for barrel pumps approved to the latest standard ATEX 1OOa (94/9/E(Z). Now, the F460 Ex EL becomes the first motor for barrel pumps which is both explosion proof and has infinitely variable speed control. This brings new precision and controllability to operations in hazardous locations. The Flux range of AC commutator motors, with explosionproof options, can be matched with a variety of the company’s pumps to provide robust, reliable solutions for a wide range of applications. The 460 Series features up-to-the-minute design to reduce running costs. Benefits
www.worldpumps.com
QUIPMENT NEWS
for the user including light weight, high power-to-weight ratio, and ease of maintenance. Contact: Brian Wigley, Flux Pumps International (UK) Limited, 12 Enterprise Park, Blackmoor Road, Verwood, Dorset BH31 6YS, UK Tel: +44 1202 823304; Fax: +44 1202 813387.
Addition vacuum range
to dry pump
batch chemical, pharmaceutical and pilot manufacturing plants. The electronic drive and control system allows flexible and intelligent operation. These are combined with in-built safety features to minimise process shutdowns due to failure of the vacuum unit. In addition, the SIHIdry ml60 can handle large quantities of liquid and particle carry-over, operates at less than 72 dB(A) noise level and because of its compact size and plug and play electronics, is particularly easy to install.
Sterling Fluid SysSterling Fluid Systems has just Contact: Theale Cross, launched the SIHIdry m 160, the tems Limited, Reading, Berks RG31 7SP, UK. latest model in its range of Tel: +44 1189 323123; Fax: +44 dry-running vacuum pumps. 1189 323302. The new pump complies with the ATEX 100 European Non-contacting Directive, which covers equipment to be used in potentially sealing for explosive atmospheres such as cryogenic pumps those found in the chemical and pharmaceutical sectors.The legislation, which will be mandato- John Crane’s new Type 285 ry as of 1st July 2003, requires non-contacting seal is the first that the complete pump, with of its kind for cryogenic pumps in process applications such as its drive unit, meets demanding safety standards before the CE liquid argon, liquid nitrogen and marking and appropriate explo- liquid oxygen. sion protection classification TheType 285 Seal’snon-concan be awarded. tacting design merges John Most dry-running vacuum Crane’s spiral groove technology with a Sealol@ welded pumps currently on the market do not comply with this direc- metal bellows, resulting in a seal tive since the temperatures that eliminates face contact and reached by the evacuated media wear, and offers precise face during the compression stage loading and excellent resistance exceed considerably the temto hang-up. This combination perature limits set by the igni- provides a significant increase tion temperature classification. in service life over existing The innovative design of the designs.The longer mean time SIHIdry ml60 (the subject of between planned maintenance several patents), features a (MTBPM) adds up to significant cost savings. For one company, sophisticated screw design, after theType 285 was applied integrated synchronised motors and drive electronics. The com- to cryogenic pumps for a fleet plete unit can be qualified to of 25 tanker trucks, savings Zone 1,T3 without the need for were achieved that amounted flame arresters. Equipped with to more than $100 000 in the flame arresters, the pump can first year alone. be used in Zone 0 applications. The Type 285 operates on a Nominal suction capacity is gas film. The small amount of heat generated at the seal interI60 Nm3/hour, with an ultimate pressure of less than 1 mbar. face vaporizes the fluid, and spiWith this performance it is very ral grooves gather and compress the gas.As the gas is foappropriate for drying, distillation and reactor filling duties in rced toward the closed groove
www.worldpumps.com
The Type 285 Seal for cryogenic applications has a non-contacting design that merges John Crane’s spiral groove technology with a Sealol@ welded metal bellows.
ends, the pressure rises and creates a gas cushion, separating the sealing faces. This spiral groove technology also minimizes product loss, reduces power consumption, and eliminates the need for costly support systems. Difficult cryogenic pump start-up conditions are combated by the Type 285 seal’s reliable face alignment capabilities. A floating carbon ring and positive drive eliminate torque transmitted to the bellows. An anti-spark sleeve, constructed of a special grade of tin bronze, provides safe operation, meeting liquid oxygen (LOX) safety standards. The compact design fits most popular cryogenic pumps available. The seal operates reliably at temperatures from -320°F (-196°C) to ambient, at pressures up to 100 psig (7 barg), and speeds up to 10 000 i-pm. Contact: John Crane’s regional headquarters - North and Latin Americas, Tel: +l 847 967 2400; Fax: +l 847 967 3915; Asia Pacific, Tel: +65 222 9161; Fax: +65 223 5035; Europe, Middle East, Africa, Tel: +44 1753 224000; Fax: +44 1753 224224.
New additions Bredel’s SPX range
to
The SPX65 and SPX80 are part of a new and advanced range of
WORLD
PUMPS
DECEMBER
1999
over the past two years the preferred option of users has been to convert existing equipment installations to achieve greater throughput. Contact: Richard Bushell, Warman International Ltd., 1 Marden Street, Attarmon NSW 2064, Australia. Tel: +61 2 9934 5100.
New line of plastic pumps Warren Rupp, Inc has launched an entirely new line of nonmetal Sandpiper II TM pumps. Models are available in sizes from 44 inch to 3 inch, with a maximum flow of 223 gal/min (844 l/min). All pumps in the new line have a rugged, bolted design. V-band clamps are not used. This results in a much stronger construction, and easier maintenance. The new pumps also feature the latest design of lubricantfree, non-stall air valve, which is more energy efficient than ever. ESADS+Plus@,the externally serviceable air distribution system, carries a money-back guarantee. The modular air valve has no close-fitting components and is very tolerant of dirty or wet compressed air. Ideal for pumping aggressive chemicals, the new plastic pumps are offered in PVDF or polypropylene, with Santoprene@’ or Teflon@ diaphragms and ball valves. Spill containment, leak detection and pulse output interface options are available for all models. Air valve, check valve cartridges and manifolds are modular in design and completely in-line serviceable.The new line provides unprecedented interchangeability of parts from model to model. Contact: Kimberlin RossPolito, Warren Rupp, lnc, PO Box 1566 Mansfield, OH 44901, USA. Tel: +l 419 524 6366; Fax: +l 419 522 7667; e-mail: [email protected]
WORLD
PUMPS
DECEMBER
1999
Multistage pump offers reduced life cycle costs Sterling Fluid Systems Limited has extended its range of modular multistage pumps with the introduction of the new Sterling multi pump. The multi range offers horizontal ring-section multistage centrifugal pumps ideal for high-pressure applications. Designed to meet the technical requirements of IS0 5199/EN 25199, the key to the success of the multi range is the adoption of an advanced modular design combined with a reduced number of parts and maximum interchangeability. Optimal selection of the impeller diameter combined with the diffuser geometry ensures the pump can be matched to the most demanding of duty requirements. In addition, the innovative design promotes reduced life cycle costs notably through the enhanced efficiency of the patented balance drum design. Avoiding tight, wear-sensitive clearances, the system incorporates a throttling device in order to control flow through the balancing line. Only one shaft seal maximises reliability whilst simple dismantling and reassembly provides a further maintenance bonus. Other special design features include a first stage impeller that ensures reliable operation with low NPSH conditions and the ability to mount the suction casing axially or radially. Contact: Sterling Fluid Systems Limited, Theale Cross, Reading, Berkshire RG31 7SP, UK Tel: +44 118 932 3123; Fax: +44 118 932 3302.
New-for-old deal for slurry pumps Svedala Ltd’s Regional Service Centres are introducing a service exchange programme for their heavy duty slurry pumps.
Customers can purchase a fully factory-refurbished Svedala slurry pump at a competitive price, in exchange for their existing worn Svedala Orion or HM pump, in all pump sizes from 50 mm (2 inch) to 200 mm (8 inch). The pumps are rebuilt in-house at the Service Centres by trained maintenance personnel, who bring the units back to within original, as-new manufactured tolerances. Each refurbished pump is backed by a 6-month warranty, and removal of the worn pump and installation of the exchange unit can also be carried out by the Service Centre for a nominal cost. In addition, the scheme will overcome problems of disposing of disused pumping equipment experienced by customers working towards the new environmental standard IS01 4000, since Svedala will effectively be offering a recycling service. Contact: Paul Beddows, Svedala UK Tel: +44 1788 532100.
Explosion-proof motor for barrel pumping Flux Pumps has introduced a new version of its Type 460 pump motor, with variable speed control. Flux claims its ~460 Ex is currently the only explosion-proof motor for barrel pumps approved to the latest standard ATEX 1OOa (94/9/E(Z). Now, the F460 Ex EL becomes the first motor for barrel pumps which is both explosion proof and has infinitely variable speed control. This brings new precision and controllability to operations in hazardous locations. The Flux range of AC commutator motors, with explosionproof options, can be matched with a variety of the company’s pumps to provide robust, reliable solutions for a wide range of applications. The 460 Series features up-to-the-minute design to reduce running costs. Benefits
www.worldpumps.com
QUIPMENT NEWS
for the user including light weight, high power-to-weight ratio, and ease of maintenance. Contact: Brian Wigley, Flux Pumps International (UK) Limited, 12 Enterprise Park, Blackmoor Road, Verwood, Dorset BH31 6YS, UK Tel: +44 1202 823304; Fax: +44 1202 813387.
Addition vacuum range
to dry pump
batch chemical, pharmaceutical and pilot manufacturing plants. The electronic drive and control system allows flexible and intelligent operation. These are combined with in-built safety features to minimise process shutdowns due to failure of the vacuum unit. In addition, the SIHIdry ml60 can handle large quantities of liquid and particle carry-over, operates at less than 72 dB(A) noise level and because of its compact size and plug and play electronics, is particularly easy to install.
Sterling Fluid SysSterling Fluid Systems has just Contact: Theale Cross, launched the SIHIdry m 160, the tems Limited, Reading, Berks RG31 7SP, UK. latest model in its range of Tel: +44 1189 323123; Fax: +44 dry-running vacuum pumps. 1189 323302. The new pump complies with the ATEX 100 European Non-contacting Directive, which covers equipment to be used in potentially sealing for explosive atmospheres such as cryogenic pumps those found in the chemical and pharmaceutical sectors.The legislation, which will be mandato- John Crane’s new Type 285 ry as of 1st July 2003, requires non-contacting seal is the first that the complete pump, with of its kind for cryogenic pumps in process applications such as its drive unit, meets demanding safety standards before the CE liquid argon, liquid nitrogen and marking and appropriate explo- liquid oxygen. sion protection classification TheType 285 Seal’snon-concan be awarded. tacting design merges John Most dry-running vacuum Crane’s spiral groove technology with a Sealol@ welded pumps currently on the market do not comply with this direc- metal bellows, resulting in a seal tive since the temperatures that eliminates face contact and reached by the evacuated media wear, and offers precise face during the compression stage loading and excellent resistance exceed considerably the temto hang-up. This combination perature limits set by the igni- provides a significant increase tion temperature classification. in service life over existing The innovative design of the designs.The longer mean time SIHIdry ml60 (the subject of between planned maintenance several patents), features a (MTBPM) adds up to significant cost savings. For one company, sophisticated screw design, after theType 285 was applied integrated synchronised motors and drive electronics. The com- to cryogenic pumps for a fleet plete unit can be qualified to of 25 tanker trucks, savings Zone 1,T3 without the need for were achieved that amounted flame arresters. Equipped with to more than $100 000 in the flame arresters, the pump can first year alone. be used in Zone 0 applications. The Type 285 operates on a Nominal suction capacity is gas film. The small amount of heat generated at the seal interI60 Nm3/hour, with an ultimate pressure of less than 1 mbar. face vaporizes the fluid, and spiWith this performance it is very ral grooves gather and compress the gas.As the gas is foappropriate for drying, distillation and reactor filling duties in rced toward the closed groove
www.worldpumps.com
The Type 285 Seal for cryogenic applications has a non-contacting design that merges John Crane’s spiral groove technology with a Sealol@ welded metal bellows.
ends, the pressure rises and creates a gas cushion, separating the sealing faces. This spiral groove technology also minimizes product loss, reduces power consumption, and eliminates the need for costly support systems. Difficult cryogenic pump start-up conditions are combated by the Type 285 seal’s reliable face alignment capabilities. A floating carbon ring and positive drive eliminate torque transmitted to the bellows. An anti-spark sleeve, constructed of a special grade of tin bronze, provides safe operation, meeting liquid oxygen (LOX) safety standards. The compact design fits most popular cryogenic pumps available. The seal operates reliably at temperatures from -320°F (-196°C) to ambient, at pressures up to 100 psig (7 barg), and speeds up to 10 000 i-pm. Contact: John Crane’s regional headquarters - North and Latin Americas, Tel: +l 847 967 2400; Fax: +l 847 967 3915; Asia Pacific, Tel: +65 222 9161; Fax: +65 223 5035; Europe, Middle East, Africa, Tel: +44 1753 224000; Fax: +44 1753 224224.
New additions Bredel’s SPX range
to
The SPX65 and SPX80 are part of a new and advanced range of
WORLD
PUMPS
DECEMBER
1999