- Email: [email protected]
ORNL develops carbon fiber joining technology
Reinforced Plastics Volume 00, Number 00 September 2016
TECHNOLOGY
Technology ORNL develops carbon fiber joining technology Oak Ridge National Laboratory (ORNL) has developed a new laser method of joining carbon fiber composites and aluminum in the manufacture of lightweight cars and other multi-material high-end products. The process, developed by a team led by Adrian Sabau, would replace the practice of preparing the surface of the materials by hand using abrasive pads, grit blasting and solvents. Using a laser to remove layers of material from surfaces prior to bonding improves the performance of the joints and provides a path toward automation for high-volume use, the lab said. ‘Our technique is vastly superior to the conventional surface preparation methods,’ Sabau claimed. ‘Combined with the potentially dramatic reduction in the cost of carbon fiber polymer composites, this represents an important step toward increasing the use of this lightweight highstrength material in automobiles, which could reduce the weight of cars and trucks by 750 pounds.’
Surface contaminants The surface treatment of aluminum and carbon fiber polymer composite is an important step in the adhesive joining process, which directly affects the quality of bonded joints. Aluminum surfaces often contain oils and other contaminants from production rolling operations while carbon fiber surfaces can contain mold releases. ‘These surface contaminants affect surface energies and the quality of adhesion,
Adrian Sabau and Jian Chen work with a laser to prepare the surface of carbon fiber composites and aluminum.
so it is critical that they are removed,’ said Sabau, adding that the laser also penetrates into the top resin layer, leaving individual carbon fibers exposed for direct bonding to the adhesive and increasing the surface area for better adhesion. In tests, the strength, maximum load and displacement at maximum load of singlelap shear joint specimens were increased by 15%, 16% and 100%, respectively, over those measured for the baseline joints. Also, joints made with laser-structured surfaces
can absorb approximately 200% more energy than the conventionally prepared baseline joints, the researchers claimed. ‘The results are most encouraging, enabling the automated processing of a multimaterial carbon fiber-aluminum joint,’ said. Tim Skszek of Magna International, a project partner. ‘With this work, we were able to focus on addressing the gaps in technology and commercial use, and we look forward to applying these findings to products.’ ORNL; www.ornl.gov
0034-3617/http://dx.doi.org/10.1016/j.repl.2016.08.026
1 Please cite this article in press as: Reinf. Plast. (2016), http://dx.doi.org/10.1016/j.repl.2016.08.026
TECHNOLOGY
Technology ORNL develops carbon fiber joining technology Oak Ridge National Laboratory (ORNL) has developed a new laser method of joining carbon fiber composites and aluminum in the manufacture of lightweight cars and other multi-material high-end products. The process, developed by a team led by Adrian Sabau, would replace the practice of preparing the surface of the materials by hand using abrasive pads, grit blasting and solvents. Using a laser to remove layers of material from surfaces prior to bonding improves the performance of the joints and provides a path toward automation for high-volume use, the lab said. ‘Our technique is vastly superior to the conventional surface preparation methods,’ Sabau claimed. ‘Combined with the potentially dramatic reduction in the cost of carbon fiber polymer composites, this represents an important step toward increasing the use of this lightweight highstrength material in automobiles, which could reduce the weight of cars and trucks by 750 pounds.’
Surface contaminants The surface treatment of aluminum and carbon fiber polymer composite is an important step in the adhesive joining process, which directly affects the quality of bonded joints. Aluminum surfaces often contain oils and other contaminants from production rolling operations while carbon fiber surfaces can contain mold releases. ‘These surface contaminants affect surface energies and the quality of adhesion,
Adrian Sabau and Jian Chen work with a laser to prepare the surface of carbon fiber composites and aluminum.
so it is critical that they are removed,’ said Sabau, adding that the laser also penetrates into the top resin layer, leaving individual carbon fibers exposed for direct bonding to the adhesive and increasing the surface area for better adhesion. In tests, the strength, maximum load and displacement at maximum load of singlelap shear joint specimens were increased by 15%, 16% and 100%, respectively, over those measured for the baseline joints. Also, joints made with laser-structured surfaces
can absorb approximately 200% more energy than the conventionally prepared baseline joints, the researchers claimed. ‘The results are most encouraging, enabling the automated processing of a multimaterial carbon fiber-aluminum joint,’ said. Tim Skszek of Magna International, a project partner. ‘With this work, we were able to focus on addressing the gaps in technology and commercial use, and we look forward to applying these findings to products.’ ORNL; www.ornl.gov
0034-3617/http://dx.doi.org/10.1016/j.repl.2016.08.026
1 Please cite this article in press as: Reinf. Plast. (2016), http://dx.doi.org/10.1016/j.repl.2016.08.026